PROGRAMMING TRANSMITTERS: NOTE: It is important to remember that during the programming mode, each individual step must be completed within 15 seconds ofthe previous step. If the 15 second time limit expires betweensteps, the unit will automatically exit the program mode. Thisis indicated by a long chirp from the siren. Non alarm models will flash the parking lights only to confirm thetransmitter code has been learned and stored. NOTE: Because the system may be capable of sounding a siren, the v

This transmitter can be used with any Audiovox unit color coded with an Orange LED in the receiver. To program this transmitter into your remote start upgrade unit: 1) Turn the ignition to the on position. 2) Press and release the programming switch 3 times. 3) Press and hold, for 3 seconds, the button of the transmitter you wish to add until the parking light flashes indicating the transmitter has been learned. 4) Repeat step 3 for each transmitter up to a total of 4. Turn the ignition of

Although this transmitter can be programmed into any of the Audiovox remote start and/or alarm, remote start systems, it will offer limited use and should be used for the remote start upgrade only. To program this transmitter into your remote start upgrade unit: 1) Turn the ignition to the on position. 2) Press and release the programming switch 3 times. 3) Press and hold, for 3 seconds, the button of the transmitter you wish to add until the parking light flashes, indicating the transmitter

Lock and arm/unlock and disarm. May be programmed to unlock driver's door or all doors. Also will initiate and terminate *Panic. Pulsed or switched output to control Remote Trunk Release or optional device connected to channel 3. When pressed and release two times, will provide pulsed output or activate the Remote Start option when installed. When so equipped, this button can be used to operate an optional device connected to channel 4. When so equipped, this button can be used to operate an opt

Before beginning this installation, carefully read through the following instructions. Use extreme care when cutting headliner material. Check for wiring or other componentry above headliner material. Cut only where indicated. Materials/ Tools required for this installation: 1. #2 Phillips screwdriver 2. Powered screwdriver or drill with adapter 3. T-15 TORX bit driver 4. Razor knife or similar 5. Awl or similar tool 6. 1/4” hex socket bit 7. 18 GA wire 4' 8. Audiovox Series 640/650 Video Module

Before beginning this installation, carefully read through the following instructions. Use extreme care when cutting headliner material. Check for wiring or other componentry above headliner material. Cut only where indicated. Materials/ Tools required for this installation: 1. #2 Phillips screwdriver 2. Powered screwdriver or drill with adapter 3. T-45 TORX bit driver 4. Razor knife or similar 5. Awl or similar tool 6. 1/4” hex socket bit 7. 7/64" drill bit 8. Small chisel 9. Audiovox Series 64

dome light area. Align the front mounting tabs with the openings in the metal inner roof openings previously used to support the rear pod retainers. Slide bracket to rear of vehicle until flange contacts rear edge of recessed area. See Figure 7. FIGURE 7 7. Secure bracket to sheetmetal frame using four (4) # 8 x 3/4" HWH TEKS screws ( item 1 pg 2 ). Secure O.E.M. ground wire (if applicable) using one of the screws. See Figure 8. FIGURE 8 6 8. If vehicle is equipped with an electronic compass, un

Failure to do so may cause damage to console or installed components. Figure 16 2. Raise overhead console into approximate position and connect wiring to O.E. components. 3. Loosely fit console against headliner. Check that console is centered in vehicle and matches all contours of headliner. While supporting console in mounting position, loosely install using two (2) 6-32 X 3/4" screws (item 10 pg 2) through the smaller holes in bracket on console into threaded clips on mounting bracket. See Fi

Cut only where indicated. Materials/ Tools required for this installation: 1. #2 Phillips screwdriver 2. Powered screwdriver or drill with adapter 3. Awl or similar tool 4. Digital Volt Meter 5. 18 GA wire 9' 6. Rubbing Alcohol 7. 5/16” Hex Socket Bit 8. Razor knife or similar 9. Pencil or equivalent 10. Measuring tape 11. Masking tape 12. Audiovox Video Module NOT FOR VEHICLES EQUIPPED WITH SUN ROOF. 128-6067 Text Box: Feb. 13,2001 Printed in the U.S.A Text Box: INSTALLATION INSTRUCTION # 44-00

Special tools and equipment, as well as specialized handling and care of product during installation, may be required. Before beginning this installation, carefully read through the following instructions. Use extreme care when cutting headliner material. Check for wiring or other components above headliner material. Cut only where indicated. Materials/ Tools required for this installation: 1. #2 Phillips screwdriver 2. Powered screwdriver or drill with adapter 3. Razor Knife or Similar 4. Di