If changing the polarity does not alleviate the problem, consult your authorized Peavey dealer, the Peavey factory, or a qualified service technician. (19) SPEAKERS These paralleled 1/4" jacks deliver your signal to the Wiggy™ 212 (or another) speaker cabinet(s). Minimum load impedance is 4 Ohms. The IMPEDANCE SELECTOR SWITCH (20) should be set for the correct enclosure load. (20) IMPEDANCE SELECTOR SWITCH This 3-position switch allows appropriate selection of speaker cabinet impedance. If t

This encoder selects any desired “rack” effect. The term Rack Effect is used to identify effect devices that would typically be found connected to the effects loop on an amplifier. These units are commonly designed to fit in a 19” wide rack, thus “rack effects.” These effects are usually POST INPUT, post EQ and SOUND DISTINCTLY DIFFERENT than PREamplifier effects (Stompboxes). To select your effect, simply turn the encoder so the LED is adjacent to the effect you desire. Octaver Just as the na

A great distorted rock guitar sound. Classic® The Peavey Classic 50® is one of the most successful amps of all time. With its responsive gain structure and warm/punchy tone Classic® series guitar amps are revered by gritty blues benders, chicken pickin’ country cats and nouveau-Stones rockers alike. Green Channel: Clean channel using normal input and presence control at 7. Red Channel: Lead channel using normal input and presence control at 7. XXX The Peavey Triple XXX® is considered by ma

Compressors can produce percussive, clicky sounds on clean guitar or mellow sustain for lead work. Try this stompbox effect on a clean channel and strike the strings softly at first and then harder to HEAR and FEEL the effect. Parameter Adjustments: PI Level, P2 Sensitivity. tompbox Encoder Ring Modulator The Ring Modulator combines two waveforms and plays the sum and difference of the frequencies present in each waveform. As you will hear this effect is certainly a little “off the wall,” but

Don’t confuse this with the Master Volume control. Power Sponge adjusts the amount of power the amp is capable of producing. This patented circuit allows you to get that full-on cranked sound at bedroom levels. 12 - Power Turn it on! Since VYPYRs have such advanced processing, they require a few moments to boot up. It’s very quick and you may not even notice it. On the VYPYR tube amplifiers you will find the addition of a Standby switch. This switch allows time to warm up the tubes. Tubes need

Don’t worry, when you plug your guitar into the amp the light show will automatically stop and will remain off for the remainder of your session. If your cable is plugged into the amp when you power on, the light show will remain off. If you want to disable the light show entirely, simply press and hold preset buttons 3 and 4 simultaneously while turning on the amp. The next time you turn on the amp, the light show will be disabled., Selection Encoders To the right of the input jack the VYPYR®

If the fuse should fail. IT MUST BE REPLACED WITH THE SAME TYPE AND VALUE IN ORDER TO AVOID DAMAGE TO THE EQUIPMENT AND TO PREVENT VOIDING THE WARRANTY. If the amp repeatedly blows fuses, it should be taken to a qualified service center for repair. WARNING: THE FUSE SHOULD ONLY BE REPLACED WHEN THE POWER CORD HAS BEEN DISCONNECTED FROM ITS POWER SOURCE. GROUND SWITCH (3) Three-position rocker-type switch which, in most applications, should be operated in its center or zero position. There may

This additional gain increases the harmonic content of the sound and is an excellent choice for the guitarist looking for a crisp sound with an intermediate amount of distortion which falls between "vintage” and “full-tilt crunch”. GAIN #2 Activating this switch opens the extra tube gain stage all the way to its voltage limits, and, as that statement indicates, maximum all-tube preamp distortion is obtained. This position yields the sound which lucky owners of custom hot-rodded tube amps have

On the lower panel, the two overdrive output jacks are located under their respective channels. The overdrive jacks incorporate a switching system to cut their respective channels away from the power amp when a plug is inserted, and then feed the output of the preamp out the patch cord for insertion into the INPUT II or 2) of the OTHER channel. Either channel is capable of driving the other and different effects can be obtained by the combined tone and volume controls. The overdrive feature is

To allow for all tastes, we have included BOTH types of tone circuits in your VTA. 1. The input jacks of your VTA are arranged in a unique switching circuit that allows added flexability in matching various input levels. Input "1" is the high gain input and should be used normally when plugging in your instrument. Input "2" is the low gain input and is to be used if the output from your instrument is overloading the high gain jack. When patching in the overdrive feature it is generally advisab