* DiSEqC applies to European systems only 3. Turn on the antenna using the switchplate, as pictured in Figure 3-2. 4. (TracVision L3 only) If the vehicle is moving, avoid turning the vehicle for 60 seconds after turning on the antenna to allow the antenna gyro to initialize properly. 3.2 Changing Channels and Switching Between Satellites If you have followed the installation instructions, your system should be set to the active satellite pair of your choice and the system should have downloaded

12. Remove the nuts and washers securing the shipping restraints to the baseplate. The positions of all three shipping restraints are pictured in Figure 2-7. 13. For convenient storage, rotate the shipping restraints 180. and secure them to their original mounting bolts using the nuts and washers removed in Step 12 (see Figures 2-8 through 2-10). All nuts and washers removed in Step 12 must be reinstalled. These nuts and washers secure the baseplate to the mounting plates. Rotating Plate Shippin

54-0157 Rev.J 2-21 A Guide to TracVision R5/R4 A Guide to TracVision R5/R4 The following is an example of configuring the fictional YOURSAT 101 as the USER1 configured satellite. Prior to configuring this satellite or any others, be certain to get the most up-to-date information from one of the sources previously discussed. Table 2-5 Sample User-defined Satellite Configuration (Europe) YOURSAT 101 at 71 West, DVB decoder, Circular Polarization LNB Horizontal High Frequency 11.966 GHz Symbol Rate

KVH® Industries’ TracVision® R5/R4 is designed for use with European and North American DVB-compatible satellite services as well as DIRECTV®. This manual provides detailed instructions on the proper installation, use, and maintenance of your TracVision R5/R4 system. Before using this manual, be sure to check for any addenda, which might detail changes to the manual’s information. Throughout this manual, important information is marked for your attention by these icons: A helpful tip that either

Who Should Install the System? To ensure a safe and effective installation, KVH recommends that a KVH-authorized marine technician install the TracVision M3 system. To find a technician near you, go to If you purchased the product and decide to install it yourself, please see the enclosed warranty statement for warranty implications. Important Safety Precaution CAUTION DO NOT apply power to the TracVision antenna with the radome removed because the antenna has moving parts that can cause injury.

TracVision S3 is designed to operate only while your vehicle is parked. Using Your TracVision L3/S3 When Parked When your vehicle is stopped, it is not necessary for the TracVision L3/S3 to be turned on. After parking your vehicle and confirming that the antenna is receiving the satellite signal, you may turn off the TracVision L3/S3 unit to avoid unnecessary use of power. Because the LNB receives its power from the IRD, the antenna will continue to receive the satellite TV signals and relay the

Aprotective cover has been added to the switchplate to guard against damaging electrostatic discharges (ESD), which may occur during installation. Figure 2-11 2.3 Connecting System Components Switchplate Cutout Dimensions 2" Figure 2-11 and the template on the following page have been changed to show the new switchplate cutout dimensions, which have been widened to accommodate the protective cover. Figure 2-13 shows the switchplate connectors as they appear within the new cover. 2.5" (Sticky Not

** If GPS is providing valid position data to the antenna, manual entry of latitude/longitude is not available. ** 2005, KVH Industries, Inc. Welcome to TracVision G8 Welcome to TracVision G8 Owner’s Manual This manual provides detailed instructions on the proper operation, installation, configuration, troubleshooting, and maintenance of the KVH TracVision G8 satellite TV system. For operation instructions, refer to the Guide to Operation. For installation, configuration, troubleshooting, and ma

3. Remove the PCB cover and set aside. 106 54-0147 Replacing the Main PCB Replacing the Main PCB . With a PC connected to the ADCU’s maintenance port, apply power to the antenna unit. 2. Record the system serial number for later re-entry (the serial number is listed at the beginning of the startup sequence, as shown in Appendix F on page 143). 3. Disconnect power from the antenna unit and the IRD. 4. Remove the PCB cover, as explained in “Removing the Main PCB Cover” on page 106. 5. Disconnect a

1.3 Materials Provided with TracVision C3 The data/power cable supplied with the system is 28 ft (8.5 m) in length. The RF cable supplied with the system is 50 ft (15 m) in length. Table 1-3 has been updated to show the correct cable lengths. Component KVH Part No. Table 1-3 Antenna Unit (comprising): 01-0225-20† 01-0225-23†† 01-0225-26††† 01-0225-29†††† TracVision C3 Packing List Baseplate Assembly 02-1245-01* 02-1245-03** Radome Assembly 02-0953-04 RF Cable (50 ft/15 m) Data/Power Cable (28 ft