Login:
Sorted: Name ↑   Downloads   Rate   Size ↑  

Ace Hardware DUALBRITE 3209996

downloaded: 0File size: 255 kb    Manafacture: Ace Hardware  
Category: Displays

Some local codes may require that a licensed electrician install the light control. This light control automatically turns on lights when motion is detected. On-time is selectable from Off, 1, 5, or 20 minutes. A photocell keeps the lights off during the day. Patented DUALBRITE® timer provides accent lighting. 1. Installation CAUTION: Always turn the circuit breaker off when wiring the fixture. 1. Remove the existing fixture. 2. After screwing the sensor into the wall plate, connect the junction

Ace Hardware DUALBRITE 3009701

downloaded: 2File size: 255 kb    Manafacture: Ace Hardware  
Category: Displays

Total lighting load including lamp- heads on fixture(s) must not exceed 500W (4.2A). Junction Box Lamp Holders CAUTION: Do not mount the sensor above or touching the lamps. Keep regular PAR-38 lamps at least 1" (25 mm) from the sensor. Halogen lamps should be kept at least 2" (51 mm) from the sensor. The sensor bottom must be facing down for best coverage and to avoid water damage and electrical shock. Note: For under-eave installation, rotate the sensor head 180° by bending the sensor towards t

Ace Hardware Door

downloaded: 0File size: 278 kb    Manafacture: Ace Hardware  
Category: Doors and Windows

Repeat the steps for “REAR” terminal and rear push button. If wiring between transformer and push button(s) check out properly, replace chime. • Check Transformer:Test transformer voltage output with a volt meter. If a volt meter is not available, momentarily touch the two low-voltage terminals with a screwdriver. You will see a small spark if transformer is operating properly. If no spark is evident, replace transformer. • Check Push Button(s):Remove suspected push button from door frame, disco

Ace Hardware ACE 3209574

downloaded: 1File size: 76 kb    Manafacture: Ace Hardware  
Category: Security Systems

1. Installation Caution: Always turn the circuit breaker off when wiring the fixture. 1. Remove the existing fixture. 2. Knockout the mounting plate holes needed to mount the sensor on the junction box. 3. Connect the light control as shown in Figure 1: •Black sensor wire to the black (HOT) house wire. •White sensor wire to the white (NEUTRAL) house wire. Black to black White to white 2. Aiming The coverage area for the sensor is shown in Figure 2. The sensor should be aimed so that the motion t

Ace Hardware ACE 3108685

downloaded: 0File size: 76 kb    Manafacture: Ace Hardware  
Category: Security Systems

At dawn, the control will reset to the motion sensing mode and shut off. This light control automatically turns the light on when motion is detected. Specifications: Total Lighting Wattage.................Up to 150 Watts Maximum Range ...........................................Up to 60 ft. Time Delay...................................1, 5, or 10 minutes Replacement lamp........................T3, Up to 150 Watt Maximum halogen 120 VAC Caution: This product is to be used with a U.L. listed rain t

Ace Hardware 3108677

downloaded: 2File size: 448 kb    Manafacture: Ace Hardware  
Category: Security Systems

You can now walk in front of the unit and the lights will come on for about 5 seconds. The TEST mode works both day and night. Walk through the coverage area and point the sensor to obtain the desired coverage area. Adjust sensitivity as needed. 4. Operation For motion sensing, put the ON-TIME switch on the bottom of the sensor in the 1, 5 or 10 minute position. When motion is detected, the lights will come on the selected time. Note: The photocell keeps the lights from turning on in daylight. T

Ace Hardware 3108669

downloaded: 1File size: 448 kb    Manafacture: Ace Hardware  
Category: Security Systems

5. Install the protective lamp shields on the lamp holders by lining up the groves on the narrow end of the shields with the dimples in the lamp holders, push the shields into the lamp holders and turn clockwise slightly. 6. Install the lamps in the lamp holders. Do not over tighten. 7. Adjustment lamp holders. The lamps should be at least 1 inch away from the sensor. Caution: Do not mount the sensor above or touching the lamps (keep 1 inch or more from the lamps). The sensor bottom must be faci

Ace Hardware 3108651

downloaded: 0File size: 448 kb    Manafacture: Ace Hardware  
Category: Security Systems

This product is ENERGY STAR® compliant when used with 120 Watt bulbs. Models 3108677/3108651/3108669 Note: Installation of this light control should be done only by those with experience in 120 Volt household wiring. Some local codes may require that a licensed electrician install the light control. This light control automatically turns on lights when motion is detected. Two lamp holders are provided. The lamp holders are rated at 150 watts max. each. 1. Installation Caution: Always turn the ci

Ace Hardware 3003530 (AC-6168)

downloaded: 1File size: 436 kb    Manafacture: Ace Hardware  
Category: Televisions

Set the chime volume on the back of the plug-in chime, if desired. 2. Plug-in the doorbell chime. To reduce the risk of electrical shock, this equipment has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way. © 2003 598-1073-02 Installation Important consi





Category