40-17,000Hz (– 3dB) Monitor Output ............................................ 50-17,000Hz (– 3dB) Noise Level Mic (– 50)...................................................... – 55dB Line (+0) ....................................................... – 57dB T.H.D. ............................................................ 0.15% @ 1KHz MIC Input Level Electronic Balanced .................................... – 50dBu MIC Output Level Switchable Electronic Balanced ................ +0 / – 50dBu Unb

Ch.1 is on the “Tip” while Ch.2 in on the “Ring”. (5) LCD Display: The twin LCD display will light up when the power is turned “ON”. The LCD displays show the following information. TV:Receive Channel Number: 30:01 – 33:47 Battery Condition: Using a 3-step indicator - 1 (Low) to 3 (High) Reception Level: Using a 4-step indicator - 1 (Low) to 4 (High) To change the TV:Receive channel number, use the tip of the tool provided and press the UP or DOWN button until the desired channel number appears

This will prevent possible crosstalk between the 2 channels being used. For example: If you use TV:Receive channel number 30:10 for one transmitter, use channel number 30:20 for the other transmitter. The 2 channels on the receiver must also be set on the numbers 30:10 and 30:20. B) The system will operate properly if both transmitters are in close proximity to each other, however make sure that both transmitters are at least 10 feet away from the receiver, this will prevent the frequencies from

Input level RF Power Input Impedance Audio Adjust. Range Battery Dimensions Weight UHF 188 Selectable Frequencies (566.125-589.875MHz) Dual-channel ReceiverPLL Synthesized-95dBm 50Hz – 15kHz >57dB (±5kHz) “A” Weighted MIC Level – unbalanced – 3.5mm Mini-Jack -64 dBm – 600 ohms @ ± 5kHz deviation -28 dBm – 600 ohms @ ± 40kHz deviation 2 “AA” Alkaline (2 x 1.5V) - 3-4 hours runtime 2 “AA” rechargeable Ni-MH (2 x 1.2V) 6VDC @ 0.5A 2.87"W x 4.45"H x 1.59"D (73 x 113 x 40.5 mm) Approx. 10.2oz (290g)

special .screw-down. connecting jack that eliminates the possibility of the jack being accidentally pulled out. A standard 3.5mm mono jack can also be used but will not afford the extra protection. (8) Metal Belt Cli. Used to attach the 32BT securely to a belt. 31XT Plug-in transmitter adaptor. Note: The 31XT is designed to turn any wired dynamic metal-body microphone that has an XLR output into . wireless microphone. Connecting the 31XT: Disconnect the microphone cable from the microphone by pu

(24) Insert two fresh Alkaline* “AA” batteries* into the compartment. Make sure the battery polarity is correct as marked inside the battery compartment. *While Alkaline batteries are preferred, you can use rechargeable Ni-Cd or Ni-MH batteries. In the battery compartment you will also find #25 and #26: (25) MIC LEVEL Control: The MIC LEVEL control enables you to adjust the audio level of the microphone. Using the supplied tool, turn the dial clockwise to increase, or counterclockwise to decreas

the same frequency. (8. Output (balanced. Using a suitable audio cable (not supplied) connect the XLR connector to the audio output on the receiver, an. connect the other end of the cable to the suitable mic/line input of an audio mixer or amplifier. 221R Two-channel VHF receiver. The 221R contains two VHF receivers operating on different frequencies. This allows single or simultaneou. use of two transmitters. The receiver features two 1/4-inch output jacks and two volume adjustments - one forea

If there is too much, or too little gain, adjust the volume on the receiver. If the soun. is distorted, move the microphone further away from the sound source. 31IT: Plug the cable into a guitar or bass. Set the instrument volume to the midway point. While playing th. instrument, adjust the volume on the mixer or amplifier to the desired level. If there is too much, or too littl. gain, adjust the volume on the receiver. If the sound is distorted lover the input gain on the 31IT. With th. system

Connect an audio cable from the output o. the receiver to a mic/line input on your audio mixer or amplifier. Plug the receiver.s AC adaptor into the 12. input jack on the receiver, and then plug it into the 110-120 VAC electrical outlet. With the volume of you. mixer or amplifier set to minimum level, turn your system.s power on. Turn on the transmitter(s). Make sur. all LEDs on the receiver and transmitter(s) are operating as described in the preceding pages. Now set th. receiver.s volume to th

WIRELESS MICROPHONE SYSTEM. OWNER.S MANUA. 311DRH . 311DR . 221R . 211R . 200R31LT . 31IT . 32BT . 32IT . 31HT . 31XT AZDEN CORPORATIO. 147 New Hyde Park Roa. Franklin Square, NY 1101. 516.328.7500 vox . 516.328.7506 fa. azdenus@aol.com . Thank you for purchasing AZDEN.S .PERFORMANCE SERIES. wireless system. This manual covers th. 311DRH, 311DR, 221R, 211R and 200R receivers and the 32BT (Lavaliere), 31XT (Plug-in XLR), 31H. (Handheld), 31LT (Lavaliere) and 31IT (Instrument) transmitters. Receiv