Login:
Votes - 2, Average rating: 4.5 ( )

User manual Audiovox, model 1181291

Manafacture: Audiovox
File size: 1.06 mb
File name: 80cbd8cf-7b1f-4a2c-8f4c-1da2a22d416a.pdf
Language of manual:en
Free link for this manual available at the bottom of the page



manual abstract


Before beginning this installation, carefully read through the following instructions. Use extreme care when cutting headliner material. Check for wiring or other componentry above headliner material. Cut only where indicated. Materials/ Tools required for this installation: 1. #2 Phillips screwdriver 2. Powered screwdriver or drill with adapter 3. T-45 TORX bit driver 4. Razor knife or similar 5. Awl or similar tool 6. 1/4” hex socket bit 7. 7/64" drill bit 8. Small chisel 9. Audiovox Series 640/650 Video Module FOR USE IN VEHICLES WITH FACTORY INSTALLED OVERHEAD CONSOLE ONLY. July 7, 1999 INSTALLATION INSTRUCTION # 44-0019E Printed in the U.S.A MATERIALS PROVIDED FOR INSTALLATION: ITEM Description QTY 1 SCREW, # 8 X 3/4" HWH 4 ,TEK,Z1 2 SCREW, # 8 X 2 1/2" PFH ,ZII 3 3 SCREW, # 8 X 1 1/4" PWH ,BZ 4 4 CONSOLE 1 5 MOUNTING BRACKET 1 6 REAR LIGHT 1 7 REAR LIGHT TRIM 1 8 PLYWOOD, 3/8" X 6" X 14" 1 9 SCREW, # 6 X 1/2" 10 10 SCREW, 6-32 X 3/4" 6 11 WASHER, 3.5 mm 4 July 7, 1999 Printed in the U.S.A INSTALLATION INSTRUCTION # 44-0019E 2 I. PREPARATION OF VEHICLE INTERIOR 1. Remove the O.E.M. compartment console currently mounted to inner roof of vehicle. Remove (1) one # 8 X 1 3/4" screw from recess in front of console near rear view mirror. Pull front of O.E.M. console down to access wiring. Disconnect all wiring from console. Pull console forward to release rear retainers from inner roof recess near center of vehicle. Remove console and lay it in a safe place. See Figure 1. 2. Turn console over and place on a covered surface. Remove plastic molded assembly from cloth covered trim ring. Using a 7/64” drill bit, drill through the center of the (10) ten plastic pins which secure console together. See Figure 2. CAUTION: Do not drill deeper than 1/2" or you may drill through console in some areas. Using a small chisel, carefully remove the head of the (10) ten plastic pins. Unsnap the wiring connector secured to clip on trim ring and separate console from trim ring. See Fig. 2. FIGURE 1 FIGURE 2 3 3. Discard trim ring. See Figure 3. Using a razor knife, carefully trim the (10) ten plastic pins flush with the shoulder. See Figure 4. FIGURE 3 FIGURE 4 4 4. Remove OEM dome light and rear air conditioning control head. Disconnect wiring and set control head aside in a safe place. Remove the OEM ground screw near the center dome light assembly if applicable. See Figure 5. FIGURE 6 FIGURE 5 5. Cut the headliner material between dome light opening and the front openings for OEM pod retainer arms. Caution: Before cutting material, check for wiring or other componentry above headliner. Cut only where indicated. See Figure 6. 5 6. Install the rear mounting bracket (item 5 pg 2 ) in the O.E.M. dome light area. Align the front mounting tabs with the openings in the metal inner roof openings previously used to support the rear pod retainers. Slide bracket to rear of vehicle until flange contacts rear edge of recessed area. See Figure 7. FIGURE 7 7. Secure bracket to sheetmetal frame using four (4) # 8 x 3/4" HWH TEKS screws ( item 1 pg 2 ). Secure ...

Other models in this manual:
Car Video - 1181292 (1.06 mb)
Car Video - 1181293 (1.06 mb)

Reviews



Your review
Your name:
Please, enter two numbers from picture:
capcha





Category