With the left side shield removed, locate the Reed Switch (43). Turn the Crank (31) until the Magnet (38) is aligned with the Reed Switch. Next, loosen, but do not remove, the indicated M4 x 16mm Screw (57). Slide the Reed Switch slightly closer to or away from the Magnet, and then retighten the Screw. Turn the Crank for a moment. Repeat until the console displays correct feedback. When the Reed Switch is correctly adjusted, reattach the left side shield and the left pedal. HANDGRIP PULSE SENSOR

until 7 p.m. Central Time (excluding holidays). To help us assist you quickly, please note the product model number before calling; the model number is 831.280781. Assembly Place all parts in a cleared area and remove the packing materials; do not dispose of the packing materials until assembly is completed. Assembly requires your standard screwdriver , phillips screwdriver and rubber mallet (not included). 1. Before attaching the Headrest (2) see drawing 1a for the proper orientation. Make sure

5. Inspect and tighten all parts regularly. Replace any worn parts immediately. 6. Keep children under the age of 12 and pets away from the 485E at all times. 7. The 485E should not be used by persons weighing more than 250 pounds. 8. Wear appropriate clothing when using the 485E. Always wear athletic shoes for foot protection. 9. When mounting and dismounting the 485E, always hold the handlebars or the T-handle and step onto and off the pedal that is in the lowest position. 10. Each time you st

2. It is the responsibility of the owner to ensure that all users of the elliptical exerciser are 9. Hold the handgrip pulse sensor or the upper adequately informed of all precautions. body arms when mounting, dismounting, or using your elliptical exerciser. 3. Your elliptical exerciser is intended for home use only. Do not use your elliptical exerciser 10. Keep your back straight while using your in a commercial, rental, or institutional set-elliptical exerciser; do not arch your back. ting. 11

Hold thehandrails and begin walking. Each workout is divided into one-minute segments. One speed setting and one incline setting are programmed for each segment. Note: The same speedsetting and/or incline setting may be programmed forconsecutive segments. During the workout, the profile will show yourprogress. The flashing segment of the profile represents the current segment of the workout. Theheight of the flashing segment indicates the speed setting for the current segment. Atthe end of each

USER'S MANUAL QUESTIONS? As a manufacturer, we are committed to providing complete customer satisfaction. If you have questions, or if parts are missing, DO NOT CONTACT THE STORE; please contact Customer Care. IMPORTANT: You must note the product model number and serial number (see the drawing above) before contacting us: CALL TOLL-FREE: 1-877-776-4777 Mon.–Fri. 6 a.m.–6 p.m. MT Sat. 8 a.m.–4 p.m. MT ON THE WEB: Model No. GGTL58608.0 Serial No. Write the serial number in the space above for refe

3. The weight bench is intended for home use only. Do not use the weight bench in any commercial, rental or institutional setting. 4. Use the weight bench only on a level surface. Cover the floor beneath the weight bench for protection. 5. Inspect and tighten all parts each time you use the weight bench. Replace any worn parts immediately. 6. Keep children under the age of 12 and pets away from the weight bench at all times. 7. Keep hands and feet away from moving parts. 8. Always wear athletic

Sears assumes no responsibility for personal injury or property damage sustained by or through the use of this product. WARNING: To reduce the risk of serious injury, read the following important precautions before using the weight system. 3 4 Leg Press High Pulley Station Backrest Ab Pulley Station Press Arm Weight Stack Right Side Left Side Note: The terms “right side” and “left side” are determined relative to a person sitting on a seat; they do not correspond to right and left on the drawing

This is especially important for persons over the age of 35 or persons with pre-existing health problems. Read all instructions before using. SEARS assumes no responsibility for personal injury or property damage sustained by or through the use of this product. 2 3 ASSEMBLED DIMENSIONS: Height: 79 in. Width: 38 in. Length: 91 in. Low Pulley Station Foot Plate High Pulley Station Leg Lever Butterfly Arms Press Arm Weight Stack Seat Backrest Thank you for selecting the versatile WEIDER® PRO 9628 H

• Assembly requires two people. Due to the size and weight of the SYSTEM 200, it should be • Tighten all parts as you assemble them, unless assembled in the location were it will be used. instructed to do otherwise. • Place all parts of the SYSTEM 200 in a cleared THE FOLLOWING TOOLS (NOT INCLUDED) ARE area and remove the packing materials; do not REQUIRED FOR ASSEMBLY: dispose of the packing materials until assembly is • Two (2) adjustable wrenches completed. • One (1) standard screwdriver • Th