FL When the drain tank switch shuts off the unit (FULL T TTANK ANKANKANK LED flashes). AS When unit disengages the compressor while the condensate pump is discharging water. HP When the high pressure switch disengages the compressor. LO Lowest temperature set point. FILTER Note: If AS does not disappear from display, contact your distributor. 9 Check the following points before calling a qualified technician. SYMPTOM SYMPTOMSYMPTOMSYMPTOM POSSIBLE CAUSE POSSIBLE CAUSEPOSSIBLE CAUSEPOSSIBLE CAUSE

....: Bar Code Handy Terminal BHT-400B-CE/400BW-CE .. DENSO WAVE INCORPORATED does not assume any product liability arising out of, or in connection with, the application or use of any product, circuit, or application described herein. .. If it is judged by DENSO WAVE INCORPORATED that malfunction of the product is due to the product having been dropped or subjected to impact, repairs will be made at a reasonable charge even within the warranty period. .. Intellectual Property Precaution DENSO W

Requests abort of transmission (Phase 2). ENQ 05h Enquiry Requests establishment of a data link (Phase 1). Prompts the receiver to respond to the sent text (Phase 2). ACK 06h Acknowledge Acknowledgment response to ENQ (Phase 1). Acknowledgment response to text (Phase 2). Acknowledgment response to EOT (Phase 3). NAK 15h Negative Acknowledge Negative acknowledgment response to ENQ (Phase 1). Negative acknowledgment response to text (Phase 2). ¦ Transparency The BHT uses the non-transparent mode w

Press individual touch-keys (¦) on the LCD. When each of them is pressed, the beeper will sound and the key will become highlighted (¦). Pressing the highlighted key again will cancel highlighting (¦). Pressing all five touch-keys (highlighting all) or C key will return to the TEST DISPLAY menu. Selecting "3:TOUCH SCREEN2" on the TEST DISPLAY menu calls up the screen shown at left. You may draw an image with the stylus in the box (graphics pad box) shown at left. Press the C key to return to the

.. Problem No file has been correctly selected for uploading. .. Solution Select a file(s) to be uploaded and retry the upload. [2.2] ActiveSync (Infrared) Choosing "2:ActiveSync (Infrared)" on the Communication menu connects the BHT to the host computer via the Infrared interface port. Upon completion of connection, the screen shown at left appears. For details about the configuration of the host computer andconnection using ActiveSync, refer to Chapter 3, Section 3.5"ActiveSync." When connecti

(5.9 mils min.) Standard 2 of 5 (STF) PCS value . 0.9 Reflection intensity difference between white and black bars . 80% CODE39 CODABAR (NW7) 0.19 mm min. (7.5 mils min.) CODE93 (PCS value . 0.45) CODE128 * The all above values are under the following conditions: • Depth of field: 68 mm (2.7") • Ambient illuminance: 500 to 3000 lux. (Xenon lamp) (2) Optical Properties Required for Bar Code Labels White bars: Reflection intensity 45% min. Black bars: Reflection intensity 25% max. PCS value 0.45 m

Specifications are subject to change without prior notice. All products and company names mentioned are trademarks or registered trademarks of their respective holders. Preface Please READ through these operating instructions carefully. It will enable you to operate your BHT-7000 correctly. After you have finished reading the instructions, keep this manual handy for speedy reference. i How this book is organized How this book is organized Chapter 1. Quick Guide Describes the basic operating meth

¦ Problem The memory has already contained 80 files, so the BHT system message file cannot be set up. ¦ Solution Press the C key to return to the SYSTEM MENU, then delete unnecessary files in the memory. (Refer to Subsection 2.5.3, [ 9 ]. ¦ Problem Uploading has failed. ¦ Solution To retry uploading, press the 1 key. To return to the SYSTEM MENU, press the 2 key. Check the interface port, communications parameters, and communications protocol type in the SET SYSTEM menu or perform the communicat

48 Chapter 2. Getting Started the BHT and System Mode If an error occurs during downloading If some error occurs during downloading, the BHT beeps three times and shows one of the following screens with the prompt "Retry?": To retry the download, press the 1 and ENT keys; to abort it, press the 2 and ENT keys. DOWNLOAD FILE. . . . . Out of memory!!. . . Retry?. 1:Yes 2:No . DOWNLOAD FILE. . . . . Too many files!!. . . Retry?. 1:Yes 2:No DOWNLOAD FILE. . . XXXXXXXX.XXX. . Communication error!!. .

¦ Solution Press the C key to return to the SYSTEM MENU and delete unnecessary files. (Refer to Chapter 2, Subsection 2.5.3, [ 9 ].) 154 Chapter 4. Error Messages ¦ Problem Uploading has failed. ¦ Solution UPLOAD FILE. . . XXXXXXXX.XXX. . Communication error!!. . . Retry?. 1:Yes 2:No To retry uploading, press the 1 key. To return to the SYSTEM MENU, press the 2 key. . Check the interface port, communications parameters, and communications protocol type in the SET SYSTEM menu or perform the commu