....: Bar Code Handy Terminal BHT-400B-CE/400BW-CE .. DENSO WAVE INCORPORATED does not assume any product liability arising out of, or in connection with, the application or use of any product, circuit, or application described herein. .. If it is judged by DENSO WAVE INCORPORATED that malfunction of the product is due to the product having been dropped or subjected to impact, repairs will be made at a reasonable charge even within the warranty period. .. Intellectual Property Precaution DENSO W

Requests abort of transmission (Phase 2). ENQ 05h Enquiry Requests establishment of a data link (Phase 1). Prompts the receiver to respond to the sent text (Phase 2). ACK 06h Acknowledge Acknowledgment response to ENQ (Phase 1). Acknowledgment response to text (Phase 2). Acknowledgment response to EOT (Phase 3). NAK 15h Negative Acknowledge Negative acknowledgment response to ENQ (Phase 1). Negative acknowledgment response to text (Phase 2). ¦ Transparency The BHT uses the non-transparent mode w

Specifications are subject to change without prior notice. All products and company names mentioned are trademarks or registered trademarks of their respective holders. Preface Please READ through these operating instructions carefully. It will enable you to operate your BHT-7000 correctly. After you have finished reading the instructions, keep this manual handy for speedy reference. i How this book is organized How this book is organized Chapter 1. Quick Guide Describes the basic operating meth

FL When the drain tank switch shuts off the unit (FULL T TTANK ANKANKANK LED flashes). AS When unit disengages the compressor while the condensate pump is discharging water. HP When the high pressure switch disengages the compressor. LO Lowest temperature set point. FILTER Note: If AS does not disappear from display, contact your distributor. 9 Check the following points before calling a qualified technician. SYMPTOM SYMPTOMSYMPTOMSYMPTOM POSSIBLE CAUSE POSSIBLE CAUSEPOSSIBLE CAUSEPOSSIBLE CAUSE

Specifications are subject to change without prior notice. All products and company names mentioned are trademarks or registered trademarks of their respective holders. Preface Thank you for purchasing this high-speed, high-accuracy assembly robot. This manual covers interfacing required when you integrate your robot system configured with the RC5 robot controller into your facilities. Before use, read this manual carefully together with related manuals to safely get the maximum benefit from you

A55537 © 1999 DENSO SALES CALIFORNIA, INC. All rights reserved. This book may not be reproduced or copied, in whole or in part, without the written permission of the publisher. DENSO SALES CALIFORNIA, INC. reserves the right to make changes without prior notice. MovinCool is a registerd trademark of DENSO Sales California, Inc. SERVICE MANUAL CLASSIC PLUS 26 FOREWORD This manual has been published to service the MovinCool Classic Plus 26. Please use this service manual only when servicing the Cl

(5.9 mils min.) Standard 2 of 5 (STF) PCS value . 0.9 Reflection intensity difference between white and black bars . 80% CODE39 CODABAR (NW7) 0.19 mm min. (7.5 mils min.) CODE93 (PCS value . 0.45) CODE128 * The all above values are under the following conditions: • Depth of field: 68 mm (2.7") • Ambient illuminance: 500 to 3000 lux. (Xenon lamp) (2) Optical Properties Required for Bar Code Labels White bars: Reflection intensity 45% min. Black bars: Reflection intensity 25% max. PCS value 0.45 m

¦ Solution Press the C key to return to the SYSTEM MENU and delete unnecessary files. (Refer to Chapter 2, Subsection 2.5.3, [ 9 ].) 154 Chapter 4. Error Messages ¦ Problem Uploading has failed. ¦ Solution UPLOAD FILE. . . XXXXXXXX.XXX. . Communication error!!. . . Retry?. 1:Yes 2:No To retry uploading, press the 1 key. To return to the SYSTEM MENU, press the 2 key. . Check the interface port, communications parameters, and communications protocol type in the SET SYSTEM menu or perform the commu

No part of this publication may be reproduced in any form or by any means without permission in writing from the publisher. Specifications are subject to change without prior notice. All products and company names mentioned in this manual are trademarks or registered trademarks of their respective holders. Preface Please READ through these operating instructions carefully. It will enable you to operate your CU-7011 correctly. After you have finished reading the instructions, keep this manua

• When the water collects to level (A) in the pump reservoir, the drain pump begins to operate and discharges the water. • When the water level drops below level (B), the drain A B pump will stop. NOTE: • If for any reason the water level exceeds that of level (A) in the pump reservoir, an overflow Drain Switch will stop the compressor operation. • If the Fan Mode Control DIP Switch (see pg.13) has been set from the COOL to the STOP position, the Fan will also turn off while the drain pump is di