¦ Problem The memory has already contained 80 files, so the BHT system message file cannot be set up. ¦ Solution Press the C key to return to the SYSTEM MENU, then delete unnecessary files in the memory. (Refer to Subsection 2.5.3, [ 9 ]. ¦ Problem Uploading has failed. ¦ Solution To retry uploading, press the 1 key. To return to the SYSTEM MENU, press the 2 key. Check the interface port, communications parameters, and communications protocol type in the SET SYSTEM menu or perform the communicat

• When the water collects to level (A) in the pump reservoir, the drain pump begins to operate and discharges the water. • When the water level drops below level (B), the drain A B pump will stop. NOTE: • If for any reason the water level exceeds that of level (A) in the pump reservoir, an overflow Drain Switch will stop the compressor operation. • If the Fan Mode Control DIP Switch (see pg.13) has been set from the COOL to the STOP position, the Fan will also turn off while the drain pump is di

No part of this publication may be reproduced in any form or by any means without permission in writing from the publisher. Specifications are subject to change without prior notice. All products and company names mentioned in this manual are trademarks or registered trademarks of their respective holders. Preface Please READ through these operating instructions carefully. It will enable you to operate your CU-7011 correctly. After you have finished reading the instructions, keep this manua

Requests abort of transmission (Phase 2). ENQ 05h Enquiry Requests establishment of a data link (Phase 1). Prompts the receiver to respond to the sent text (Phase 2). ACK 06h Acknowledge Acknowledgment response to ENQ (Phase 1). Acknowledgment response to text (Phase 2). Acknowledgment response to EOT (Phase 3). NAK 15h Negative Acknowledge Negative acknowledgment response to ENQ (Phase 1). Negative acknowledgment response to text (Phase 2). ¦ Transparency The BHT uses the non-transparent mode w

(SET POINT temperature equals inlet air or room temperature.) The unit has been preset at the factory for continuous fan operation. • Temperature Scale Display DIP Switch The Temperature Scale Display DIP Switch changes the temperature(s) that are displayed to either °C or °F. The unit has been preset from the factory to display the temperature(s) in °F. NOTE: If you wish to change the fan mode operation (COOLOPERATE to COOLSTOP), and/or the Temperature Scale Display (°F to °C), contact your Mov

¦ Solution Press the C key to return to the SYSTEM MENU and delete unnecessary files. (Refer to Chapter 2, Subsection 2.5.3, [ 9 ].) 154 Chapter 4. Error Messages ¦ Problem Uploading has failed. ¦ Solution UPLOAD FILE. . . XXXXXXXX.XXX. . Communication error!!. . . Retry?. 1:Yes 2:No To retry uploading, press the 1 key. To return to the SYSTEM MENU, press the 2 key. . Check the interface port, communications parameters, and communications protocol type in the SET SYSTEM menu or perform the commu

If dust and/or dirt are present, wipe off with a clean, dry cloth. . Check the power cord, plug and prongs for damage or excess play. If any damage or excess play is found, contact your MovinCool reseller for repair. . Clean the air filters. . Empty all water from the drain tank. 16 TROUBLESHOOTING Self-Diagnostic Codes Self-Diagnostic Codes will be displayed on the Control Board under the following conditions: Code Condition dF When the evaporator thermistor disengages the compressor. FL When t

• The Office Pro 36 is equipped with a six (6) foot (1.8 meter) AFCI power cord. If replacement, fixed location (hard wired) or power cord lengthening (extension cord) cords are required, contact your reseller or a qualified licensed electrician for approved replacement methods. • Never fold, or place heavy objects on the power cord. This could result in damage to the power cord causing electrical shock or fire. • Do not place water or any other liquid on the unit. This can cause damage to the u

.. Problem No file has been correctly selected for uploading. .. Solution Select a file(s) to be uploaded and retry the upload. [2.2] ActiveSync (Infrared) Choosing "2:ActiveSync (Infrared)" on the Communication menu connects the BHT to the host computer via the Infrared interface port. Upon completion of connection, the screen shown at left appears. For details about the configuration of the host computer andconnection using ActiveSync, refer to Chapter 3, Section 3.5"ActiveSync." When connecti

Specifications are subject to change without prior notice. All products and company names mentioned are trademarks or registered trademarks of their respective holders. Preface Thank you for purchasing this high-speed, high-accuracy assembly robot. This manual covers interfacing required when you integrate your robot system configured with the RC5 robot controller into your facilities. Before use, read this manual carefully together with related manuals to safely get the maximum benefit from you