Low Battery Parent Unit • When the battery is low in the parent unit you may hear static or other noise. You may either plug in the A/C adapter or replace the batteries. Out of Range Indication • If the Parent Unit begins to lose the signal from the Nursery Unit you may hear static or other noise. Immediately move the Parent Unit closer to the Nursery Unit to regain connection. ***Note: It is not uncommon for the Parent Unit to occasionally lose and regain connection with the Nursery Unit in env

visit us online at We currently do not accept product registrations from those living outside the United States of America. OWNER'SMANUAL-Keepinstructionsforfutureuse. POWERPOWER72°F//2M022M03Product Features POWERPOWER VOL. OFFACHANNELB- + 9VDCPower Volume: Up/Down Channel Selector Clip DC Adapter Jack Battery Cover Parent Unit (2) AC Adapter (2) ©2005 Graco ISPM005BA 10/05 Nursery Unit Model 2M02 Nursery Unit Model 2M03 Channel Selector ON/OFF Night Light Button POWERNight Light Face plates (3

REF REF NO. PART NO. DESCRIPTION QTY NO. PART NO. DESCRIPTION QTY 10 218–973* PRIMING VALVE KIT 1 45 181–159 NUT, coupling 1 11 181–152 GUIDE, diaphragm 1 46 181–160 NlPPLE, hose 1 15 108–225 CAPSCREW, socket head; 47 108–231 CLAMP, hose 2 5/16–18x 1–1/8” long 4 48 181–163 HOUSING, filter 1 16 104–008 LOCKWASHER, spring, 5/16” 4 49 181–164 FILTER 1 17 275–619* DIAPHRAGM 1 52 178–342 CLAMP, hose 2 18 218–981 CONNECTING ROD & BEARlNG 1 53 181–613** LABEL, Warning 1 20 108–237 CAPSCREW, socket head

. Keep the application area free of debris, including solvent, rags, and gasoline. SKIN INJECTION HAZARD If high-pressure fluid pierces your skin, the injury might look like “just a cut”. But it is a serious wound. Get immediate surgical treatment. To help prevent injection . Keep your hands and body away form the roller frame when flushing. High pressure fluid emitted from the holes in the frame could cause an injection injury. . Always relieve pressure before you check or repair leaks and when

1. Shut off the pump or sprayer. 2. Trigger the gun. 3. Open the gun air valve. 4. Disconnect the power source. Grounding To reduce the risk of electric shock, proper electrical grounding is essential. See your separate pump or sprayer instruction manual, and consult your local electrical codes for detailed grounding instructions. Working Pressure To reduce the risk of component rupture and serious bodily injury, never exceed 100 psi (7 bar) AIR OR FLUID WORKING PRESSURE to this gun. Do not exce

Lubricate the screws (15) and loosely install them and the lockwashers (16). Torque the screws a few inch–pounds (N.m) at a time, oppositely and evenly, to 85 in–lb (9.6 N.m). 10. Reinstall the front cover (23). Fig 16 9 LUBRICATE TORQUE TO 85 in–lb (9.6 N.m) 15,16 42 43 33 22 24 23 69 34 30 21,20 18a 1818b PRESS FIT INTO 22 GREASE BEARING HEAVILY A 39 IN OUT MOTOR LEADS Fig 17 RED (+) Motor (See Fig 16 and 17.) 1. Remove the front cover (23). 2. Remove the base cover (42). Disconnect the motor

. Do not stop or deflect leaks with your hand, body, glove or rag. . Tighten all connections before operating the equipment. . Check the hoses, tubes, and couplings daily. Replace worn, damaged, or loose parts immediately. Permanently coupled hoses cannot be repaired; replace the entire hose. . Use only Graco approved hoses. Do not remove any spring guard that is used to help protect the hose from rupture caused by kinks or bends near the couplings. FIRE AND EXPLOSION HAZARD . If there is any st

Do not remove any spring guard that is used to help protect the hose from rupture caused by kinks or bends near the couplings. FIRE AND EXPLOSION HAZARD . If there is any static sparking or you feel an electric shock while using this equipment, stop dispensing immediately. Do not use the equipment until you identify and correct the problem. . Keep the dispensing area free of debris, including solvent, rags, and gasoline. . Electrically disconnect all equipment in the dispensing area. . Extinguis

PRESSURE WASHER TERMINOLOGY PSI: Pounds per Square Inch. The unit of measure for water pressure. Also used for air pressure, hydraulic pressure, etc. GPM: Gallons Per Minute. The unit of measure for the flow rate of water through the pressure washer. CU: Cleaning Units. GPM multiplied by PSI. Bypass Mode: In Bypass Mode, the pump is recirculating water because the trigger of the spray gun is not pulled. Chemical Injection: Feeds cleaning agents into the pump to mix with the pressurized water and

BEFORE PERFORMING ANY MAINTENANCE OR REPAIR, DISCONNECT SPARK PLUG WIRE, LET ENGINE COOL AND RELEASE ALL WATER PRESSURE. THE ENGINE CONTAINS FLAMMABLE FUEL. DO NOT SMOKE OR WORK NEAR OPEN FLAMES WHILE PERFORMING MAINTENANCE. To ensure efficient operation and longer life of your pressure washer, a routine maintenance schedule should be prepared and followed. If the pressure washer is used in unusual conditions, such as high-temperatures or dusty conditions, more frequent maintenance checks will b