Votes - 5, Average rating: 4.6 ( )

Manafacture: Graco Inc. File size: 1.01 mb File name: Language of manual:

Low Battery Parent Unit • When the battery is low in the parent unit you may hear static or other noise. You may either plug in the A/C adapter or replace the batteries. Out of Range Indication • If the Parent Unit begins to lose the signal from the Nursery Unit you may hear static or other noise. Immediately move the Parent Unit closer to the Nursery Unit to regain connection. ***Note: It is not uncommon for the Parent Unit to occasionally lose and regain connection with the Nursery Unit in environments that have a significant amount of obstructions. 3 Selecting Channels Selecting Channels • In case you are experiencing some interference, the channel on the Nursery Unit can be changed by switching the channel button on the side of the unit. The Parent Unit and Nursery Unit must both be set to the same channel, either channel “A” or “B” (“X” or “Y”). Night Light or Temperature • Some models have a night light on the Nursery Unit that will illuminate when the button on the top of the unit is pressed and will automatically shut off in 15 minutes or push the button again to turn the light off. • Some models will display the temperature of the Nursery Unit. Push the button on the front of the Nursery Unit to switch from °F to °C. Setting Up the Baby Monitor 1. For optimum operation, it is best to use new batteries in the Parent Unit. 2. Place the Nursery Unit within 10 feet (3 meters) of your baby. Plug an AC adapter into the jack on the side of the Nursery Unit. Plug it into a working 120 volt AC outlet. 3. Aim the Nursery Unit toward your baby. Check that there are no walls or large objects that could block sound transmission. 4. Set both the Nursery Unit and Parent Unit to the same channel, “A” or “B” (“X” or “Y”). 5. Turn on the Nursery Unit using the On/Off switch on the side. The green power light should come on. 6. Place the Parent Unit within five (5) feet (1.5 meters) of the Nursery Unit and turn on the Parent Unit using the On/Off switch on the side of the unit. The green power light should come on. 7. Repeat same set-up procedure for second Parent Unit. 8. Your monitor is now ready for use. 4 Testing the System Testing the System It is VERY IMPORTANT to test the system when first set up, and at regular times thereafter. Test the units if you suspect they may have been damaged or have not been used for a long time. 1. If two adults are present, have one take the Parent Unit(s) to different locations, trying various volume settings, while the other speaks into the Nursery Unit. 2. If only one adult is available, place a ticking clock, radio, or other sound-producing device near the Nursery Unit to test it. 3. When testing, keep the level of your child’s sounds in mind, and adjust the volume accordingly. 4. If there is sound interference, switch the Nursery Unit and the Parent Units to the other channel setting. Operation To Listen To Baby • Turn on Nursery Unit using the ON/OFF switch. • Turn on Parent Unit(s) using the ON/OFF switch. • Adjust the volume on the Parent Unit by turning the Volume Up/Down knob. • The Sound Lights on the Parent Unit will illuminate as your child (or other objects) make noise near the Nursery Unit. Please note that the Sound Lights and volume control on the Parent Unit are independent of each other. With the volume turned all the way down, the Sound Lights will still illuminate as your child (or other objects) make noise near the Nursery Unit. To change the face plate: • Pull the bottom of the face plate out from the bottom of the Nursery Unit. • Lift the face plate up and pull the top out of the Nursery Unit . • Reverse the steps to replace with the desired face plate. Face Plate (on certain models) 5 TroubleShooting TroubleShooting DO NOT ATTEMPT to modify the unit. Any modifications to the transmitter and/or receiver can void the operator’s authority to operate the equipment. Most problems have a simple solution. First, check that: • Power is turned ON for both units • Both units are plugged in (or batteries are fresh in Parent Unit) • Electrical outlet works • Volume is turned up on Parent Unit • Parent Unit is in range of the Nursery Unit No Sound • Battery dead or weak — replace or use AC adapter. • AC adapter not properly connected — check the connections. • Nursery Unit covered or blocked — remove the obstruction. Weak Sound • Nursery Unit too far from baby — move closer. • Large objects blocking the signal — try repositioning Nursery Unit. • Volume setting too low — turn it up. Static • Interference from other electrical equipment — eliminate cause of static (TVs, mixers, computers, fans, fluorescent lights, light dimmers, etc.) • Parent Unit too far from Nursery Unit — move them closer. • Significant amount of obstructions between Parent Unit and Nursery Unit such as walls, ceilings & buildings. Try moving the Nursery Unit to another part of the room. Shrill Sound (Feedback) • Nursery Unit and Parent Unit too close together — move them farther apart. • Volume set ...

Download now

Please, enter two numbers from picture: