Login:
Sorted: Name ↓   Downloads   Rate   Size ↑  

Graco Inc. 1095 HI

downloaded: 3File size: 3 mb    Manafacture: Graco Inc.  
Category: Paint Sprayers

Save these instructions. 695/795 HI 695/795 LOW MARK V 1095/1595 HI ti7363b Warnings Warnings The following warnings are for the setup, use, grounding, maintenance and repair of this equipment. The exclamation point symbol alerts you to a general warning and the hazard symbol refers to procedure-specific risks. Refer back to these warnings. Additional, product-specific warnings may be found throughout the body of this manual where applicable. Grounding Instructions This product must be grounded.

Graco Inc. 1095 Premium Hi

downloaded: 7File size: 3 mb    Manafacture: Graco Inc.  
Category: Paint Sprayers

If plug will not fit in outlet, have grounded outlet installed by a qualified electrician. Do not use an adapter. Power Requirements • 100-120V units require 100-120 VAC, 50/60 Hz, 15A, 1 phase. • 230V units require 230 VAC, 50/60 HZ, 10A, 1 phase. Extension Cord Use an extension cord with an undamaged ground contact. If an extension cord is necessary, use a 3-wire, 12 AWG (2.5 mm2) minimum. Pails Solvent and oil/based fluids: follow local code. Use only conductive metal pails, placed on a groun

Graco Inc. 1095 Premium Hi-Boy

downloaded: 1File size: 5 mb    Manafacture: Graco Inc.  
Category: Paint Sprayers

10. Leaking around throat packing nut which may indicate worn or damaged packings. 10. Replace packings; see pump manual. Also check piston valve seat for hardened paint or nicks and replace if necessary. Tighten packing nut/wet-cup. 11. Pump rod damage 11. Repair pump. See pump manual 310643 or 310894. 12. Low stall pressure 12. Turn pressure knob fully clockwise. Make sure pressure control knob is properly installed to allow full clockwise position. If problem persists, replace pressure transd

Graco Inc. 111418a

downloaded: 1File size: 3 mb    Manafacture: Graco Inc.  
Category: Paint Sprayers

. 248684 . . 248685 . . 248686 . . GMAX ll 5900 248687 . . 248688 . . 248689 . . 248690 . . GMAX II 5900HD 248699 . . GMAX ll 5900 Convertible 248691 . . 248692 . . 248693 . . 248694 . . 248695 . . 248696 . . 248697 . . 248889 . . 248890 . . GMAX ll 7900 248700 . . 248701 . . 248702 . . 248703 . . TexSpray 5900 HD Convertible 255630 . . 255631 . . 255954 . . TexSpray 7900 HD 255632 . . ti5474a ti5475a ti5447a ti11418a 310893 311046 311861 310894 309640 Manual Conventions Manual Conventions WARNI

Graco Inc. 12004

downloaded: 0File size: 1014 kb    Manafacture: Graco Inc.  
Category: Paint Sprayers

Save these instructions. See page 2 for part numbers and maxumum working pressure. Model 12004X Models 12004 and 12005 Model 12006 309739D Models Models Pistol Grip, Base Seal Pistol Grip, Tip Seal Part Number Model Description 2500 psi (17.2 MPa, 172 bar) maximum working pressure C27020 12004 Standard base seal C27031 12004X Two stage, easy pull C27067 12005 Balanced piston Part Number Model Description 2000 psi (13.79 MPa, 137.9 bar) maximum working pressure C27078 12006 Pistol Grip, Tip Seal

Graco Inc. 12004X

downloaded: 2File size: 1014 kb    Manafacture: Graco Inc.  
Category: Paint Sprayers

Then loosen it completely. Clear tip/nozzle or hose. Trigger Lock Always engage trigger lock when you stop dispensing to prevent gun from being triggered accidentally by hand or if dropped or bumped. To engage trigger lock, release trigger and rotate lock downward. See Fig. 1. To disengage trigger lock, rotate it upward. See Fig. 2. If material hose will be suspended by a hanger or tool balancer, route hose through the suspension device before securing each end of material hose. To help prevent

Graco Inc. 12005

downloaded: 3File size: 1014 kb    Manafacture: Graco Inc.  
Category: Paint Sprayers

Check them carefully for damage or wear, replacing parts as needed. For best results replace the original parts with new parts in repair kits. Prior to assembly, lubricate all seals and o-rings with PARKER-O-LUBE or an equivalent lubricant. 1. Connect needle (8) and stop nut (2) to yoke (1). 2. Secure yoke (1) in soft jawed vise. Lock stop nut (2) against yoke. ti4043a 3. Insert needle (8) into packing nut (5). 4. Push three seal needles (6) in packing nut (5) using soft rod or dowel. Orient as

Graco Inc. 12006

downloaded: 4File size: 1014 kb    Manafacture: Graco Inc.  
Category: Paint Sprayers

12. While holding adapter stationary, screw collar (17) and nozzle (18) into adapter. Do not overtighten collar. 13. Reconnect flow gun to material supply line. 14. Turn on material supply line. 15. Return flow gun to normal operating condition. 309739 11 Parts 12 309739 Parts Models 12004 & 12004X 13 1 2 5 3 6 4 7 11 23 12 16 9 10 8 15 14 17 18 21 19 20 Item Part No. Description Qty 1 C27052 YOKE 1 2 100284 NUT, hex (model 12004) 1 C19284 NUT, hex (model 12004-X) 1 3 C27061 SCREW, adjustment 1

Graco Inc. 150 RPX

downloaded: 1File size: 1 mb    Manafacture: Graco Inc.  
Category: Other Tools

Flush the pump, In–line Valve and pressure roller immediately after each use to prevent paint from drying in the pressure roller and damaging it. Cleanup page 17. 14 309388 Rolling Techniques 1. Rolling vertically, roll out the letter “M”. 2. Cross roll, horizontally, to spread the paint. 3. Finish with light vertical strokes until the entire area has been evenly covered. 309388 15 Ceilings, Woodwork and Walls 1. Ceilings: Using a paint brush, apply a starting row of paint approximately the widt

Graco Inc. 1595 HI

downloaded: 5File size: 3 mb    Manafacture: Graco Inc.  
Category: Paint Sprayers

When the unit is not in use, turn off the unit and follow the Pressure Relief Procedure for turning off the unit. • High-pressure spray is able to inject toxins into the body and cause serious bodily injury. In the event that injection occurs, get immediate surgical treatment. • Check hoses and parts for signs of damage. Replace any damaged hoses or parts. • This system is capable of producing 3300 psi. Use Graco replacement parts or accessories that are rated a minimum of 3300 psi. • Always eng





Category