• Store flammable materials in a secure location away from compressor. • Never place objects against or on top of compressor. • Operate compressor in an open area at least 12" (304.8 mm) away from any wall or obstruction that would restrict the flow of fresh air to the ventilation openings. • Operate compressor in a clean, dry well ventilated area. Do not operate unit indoors or in any confined area. • Always remain in attendance with the product when it is operating. • Always turn off and unplu

Like any other electrically powered device, If it is not used properly it may cause electric shock. • Never operate the compressor outdoors when it is raining or in wet conditions. • Never operate compressor with protective covers removed or damaged. • Never operate compressor with damaged or worn cords. • Repairs attempted by unqualified personnel can result in serious injury or death by electrocution. • Any electrical wiring or repairs required on this product should be performed by authorized

Some air tools and accessories may require filtered air. Read the in struc tions for the air tools and accessories. How to Start 1. Set the On/Off switch to "On" and allow tank pressure to build. Motor will stop when tank pressure reaches "cut-out" pressure. 2. Turn regulator knob clockwise to increase pressure and stop when desired pressure is reached. If any unusual noise or vibration is noticed, stop the compressor immediately and have it checked by a trained service technician. The compresso

Motor Overload Protector (not shown): The motor has an automatic reset thermal overload protector. If the motor overheats for any reason, the overload protector will shut off the motor. The motor must be allowed to cool down before restarting. The compressor will automatically Check Valve restart after the motor cools. HOW TO USE YOUR UNIT How to Stop 1. Set the On/Off switch to "Off". Before Starting Do not operate this unit until you read and understand this Break-in Procedure instruction manu

4. Sanding of lead-based paint is not recommended. Lead-based paint should only be removed by a professional. 5. Always keep the base of the sander in contact with a secure workpiece to prevent loss of control. 6. Do not operate Oscillating Sander without all guards and covers securely in place. 7. Some wood contains preservatives which can be toxic. Take extra care to prevent inhalation and skin contact when working with these materials. Request, and follow, any safety information available fro

Make a 3/64" cut by setting the lever halfway between “1” and “2”. The plane has one other operating adjustment - the angle of the apron to the plane shoe. This adjustment consists of two graduated hinges held by wing nuts (E) Fig. 6. Both hinges should be on the same angle markings before the nuts are tightened. D E Fig. 6 10 HOW TO USE THE PORTA-PLANE® MAKING THE CUT To provide maximum control of the tool, hold the planer with the right hand on the handle and the left hand on the front of the

Postfach 30 D-73461 Westhausen Safety Recommendations For your safety and the safety of others, read and understand the safety recommendations before operating this saw. Always wear protective equipment. WARNING! Impact resistant eye protection must be worn while operating or working near this tool. Caution: Faceshields do not provide unlimited protection against flying particles and are not to be considered as eye protection. ANSI Z87.1 states that separate eyewear shall be used. For additional

Wear protective hair covering to contain long hair. 9. USE SAFETY GLASSES. Wear safety glasses or goggles while operating power tools. Also face or dust mask if operation creates dust. All persons in the area where power tools are being operated should also wear safety glasses and face or dust mask. 10. DON’T ABUSE CORD. Never carry tool by cord or yank it to disconnect from receptacle. Keep cord from heat, oil, and sharp edges. Have damaged or worn power cord and strain reliever replaced imme

plate is located on the main housing of the tool. Record these numbers in the spaces below and retain for future reference. Model No. ______________________________________ IMPORTANTPlease make certain that the person who is to use this equipment carefully reads and understands these instructions before starting operations. ESPANOL: PAGINA 9 FRANCAISE : PAGE 19 MODEL 2640 (10 Ft. Cord) MODEL 2650 (50 Ft. Cord) Type ___________________________________________ Serial No.___________________________

Do not use tool if switch does not turn it on and off. 20. WEAR EAR PROTECTION to safeguard against possible hearing loss. SAVE THESE INSTRUCTIONS REPLACEMENT PARTS When servicing use only identical replacement parts. ADDITIONAL SAFETY RULES FOR SCREWDRIVERS 1. VERIFY direction of rotation of screwdriver is correct for operation to be performed before starting tool. 2. DO NOT attempt to change direction of rotation while switch is “ON”. To do so may damage interlock feature built into switch. Be