Login:
Sorted: Name ↓   Downloads   Rate   Size ↑  

Dakota Digital 650360

downloaded: 0File size: 256 kb    Manafacture: Dakota Digital  
Category: Time Clocks

This module can be used as a simple clock display or it can display data from any BIM module attached to the system as well as several gauge values from the control box sensors. Most versions of this module come with at least one switch in the face to allow the display to change between various screens. Some versions may also contain two additional switches in the face which can be used as the SW1 and SW2 for the VHX control box with the use of the switch harness provided with it. CONNECTION: Th

Dakota Digital CLK-1002B

downloaded: 0File size: 67 kb    Manafacture: Dakota Digital  
Category: Time Clocks

Top “set” button advances hours, bottom “set” button advances minutes. Each time that you make a change to either the hours or minutes, the seconds are reset to zero. Adjusting the accuracy: The clock is accurate to +/-2 minutes a month as it is sent. It can be tuned for better accuracy if desired. Press and hold both of the set buttons for several seconds. The clock will display “C 0”. The “C” indicates that it is in the calibration mode and the second number is the current calibration value. T

Dakota Digital CMD-4000

downloaded: 6File size: 185 kb    Manafacture: Dakota Digital  
Category: Security Systems

A 4+ FUNCTION REMOTE CONTROL DOOR LATCH OPENER SYSTEM INTRODUCTION Thank you for purchasing the CMD-4000 series Remote Control Door Latch Opener System from Dakota Digital, Inc. This, along with many other products that Dakota Digital, Inc. has to offer, represents the latest in electronics technology for the street rod, classic car and truck, and any custom vehicle. The CMD-4000 Remote Control Door Latch Opener system comes complete with receiver, two key chain transmitters, wiring harness,

Dakota Digital DAKOTA DIGITAL PAC-2700

downloaded: 10File size: 124 kb    Manafacture: Dakota Digital  
Category: Fans

(A second relay, sold separately, is required for two speed or dual fan operation). The controller monitors the engine temperature using a dedicated sender, or a gauge and its sender. When the engine temperature goes above a user adjustable set point, the fan is turned on with a relay. When the engine has cooled below a user selectable off temperature, the fan is shut off. Separate on and off temperatures can be set for the high and low fan outputs. The controller will also run the fan when the

Dakota Digital ION-16

downloaded: 2File size: 53 kb    Manafacture: Dakota Digital  
Category: Time Clocks

BLUE - Night Dimming: connect to the head light switch. BLACK - connect to a main ground location Mounting: The gauge requires an oval hole 1-7/16” high x 3-1/16” wide. It should be inserted into the opening from the front and the 2 L-clamps will be installed from the back. Tighten a nut on each of the L-clamps so that the gauge is secure. Gauge depth to the back of the case is 1”. Gauge depth including the mounting studs is 1-7/8”. Operation: The gauge needs the red, orange, and black wires con

Dakota Digital LAT-NR261

downloaded: 4File size: 119 kb    Manafacture: Dakota Digital  
Category: Work and Flash Light

If the gasket is hard or brittle it should be replaced. 4. Now is a good time to clean or replace the lenses and housings if necessary. If the lenses are in poor condition a replacement set is recommended. MAN#650217 5. Insert the LED assembly bulb base into the tail light housing socket. 6. Place the new LED assembly into the housing so that the aluminum mounting bracket sits into the groove for the lens gasket. 7. Replace the lens gasket. The gasket will sit on top of the aluminum mountin

Dakota Digital LAT-NR391

downloaded: 3File size: 157 kb    Manafacture: Dakota Digital  
Category: Work and Flash Light

2. Remove the plastic housing from the vehicle. 3. Remove the tail light lens by gently prying the housing away from the lens tabs. 4. Now is a good time to clean the lens and housing. If lenses are in bad shape a new set is recommended. 5. Remove the round mounting plate from the bottom of the LED assembly. It is attached with two lock nuts. 6. Insert each new LED assembly through the hole where the original bulb and connector were located. Use caution when feeding the wires through the socket

Dakota Digital LAT-NR402

downloaded: 1File size: 202 kb    Manafacture: Dakota Digital  
Category: Work and Flash Light

4. Remove the tail light lens. 5. Now is a good time to clean the lens and housing. If lenses are in bad shape a new set is recommended. 6. Remove the lock nuts and aluminum back plate from the back of the new LED assembly. 7.Insert the new LED assembly through the hole where the original bulb and connector were. Use caution when feeding the wires through to avoid damaging the wire insulation. 8.Feed the wires through the large hole in the back plate and attach the back plate onto the backside o

Dakota Digital LED Tail Lights for 1957 Chevy Car LAT-NR210

downloaded: 0File size: 127 kb    Manafacture: Dakota Digital  
Category: Work and Flash Light

2. Remove the light bulb 3. Push and twist to remove the plastic wire socket from the back side of the housing. 4. Now is a good time to clean the lens and housing. If lenses are in bad shape a new set is recommended. 5. Remove the lock nut and flat plastic back plate from the back of the new LED assembly. 6. Make sure that one wire is still going through each hole in the aluminum spacer. Insert the new LED assembly through the hole where the original bulb and connector were located. Use caution

Dakota Digital LED Tail Lights for 1969 Camaro LAT-NR111

downloaded: 0File size: 182 kb    Manafacture: Dakota Digital  
Category: Work and Flash Light

Remove the original bulb connectors from the bottom side of the housing. 2. Remove the plastic housing from the vehicle. 3. Remove the tail light lens by gently prying the housing away from the lens tabs. 4. Now is a good time to clean the lens and housing. If lenses are in bad shape a new set is recommended. 5. Note that the screws and mounting plates are assembled differently for the driver side set and passenger side set. The LED assemblies will sit in the housing at an angle similar to the b





Category