Login:
Sorted: Name ↑   Downloads   Rate   Size ↑  

Dakota Digital MAN#650277

downloaded: 16File size: 267 kb    Manafacture: Dakota Digital  
Category: Boats Accessories

Remove the clusters from the vehicle. The procedure for the speedometer and tachometer clusters are the same, but only one side is shown in the photos. 2. Remove the three screws holding the bezel on to the gauge can. Two are indicated by the upper arrows in the photo at right; one is on the bottom side of the can and cannot be seen here. After the bezel is set aside, remove the two screws near the center of the can to remove the original gauge. On the speedometer can (shown) you will also need

Dakota Digital DAKOTA DIGITAL PAC-2700

downloaded: 10File size: 124 kb    Manafacture: Dakota Digital  
Category: Fans

(A second relay, sold separately, is required for two speed or dual fan operation). The controller monitors the engine temperature using a dedicated sender, or a gauge and its sender. When the engine temperature goes above a user adjustable set point, the fan is turned on with a relay. When the engine has cooled below a user selectable off temperature, the fan is shut off. Separate on and off temperatures can be set for the high and low fan outputs. The controller will also run the fan when the

Dakota Digital PAC-3500

downloaded: 8File size: 67 kb    Manafacture: Dakota Digital  
Category: Doors and Windows

3Speeds are approximate and may vary slightly depending on application Wiring to a door lock motor. Dakota Digital RLY-2 relay pack shown. To PAC-3500Lock output. FUSED 12V POWERTo PAC-3500Unlock output. The wires between the switch and the motor will need to be cut, and the relay pack wired in between as shown. Fused 12V power. MOTORMOTORSWITCHPURPLEGREENBROWNWHITEBLUERELAYREDsmall wireGREENPACKBLUEsmall wireDUAL+12v on lock+12v on lock Indicator LEDs The green LED will turn on when the auto-lo

Dakota Digital CMD-4000

downloaded: 6File size: 185 kb    Manafacture: Dakota Digital  
Category: Security Systems

A 4+ FUNCTION REMOTE CONTROL DOOR LATCH OPENER SYSTEM INTRODUCTION Thank you for purchasing the CMD-4000 series Remote Control Door Latch Opener System from Dakota Digital, Inc. This, along with many other products that Dakota Digital, Inc. has to offer, represents the latest in electronics technology for the street rod, classic car and truck, and any custom vehicle. The CMD-4000 Remote Control Door Latch Opener system comes complete with receiver, two key chain transmitters, wiring harness,

Dakota Digital UTV-1500

downloaded: 5File size: 289 kb    Manafacture: Dakota Digital  
Category: Boats Accessories

UTV-1500 Gauge for Polaris RZR MPHABTEMPOILkm/hEFVOLTSFUEL1234567SERVHRTachometer bar graphSpeed displayLight sensor locationMessage centerSpeed unit indicators4x4 on indicatorCheck engine indicatorGear position indicatorsFuel bar graph Operation menu Switch functions: Pressing the switch during normal gauge operation will move the message center through the below display functions. ... Odometer ... A Trip odometer A (hold switch to reset) ... B Trip odometer B (hold switch to reset) SERV ......

Dakota Digital MULTI GAUGE UTV-1200

downloaded: 5File size: 130 kb    Manafacture: Dakota Digital  
Category: Time Clocks

UTV-1200 Multi Gauge for 2008 Yamaha Rhino Operation menu Left switch functions Pressing the left switch during normal gauge operation will move through the below commonly viewed functions for convenience. 00000.0 Odometer 12:00A Clock (hold left switch to set) Setting clock: Left switch press moves between hours and minutes Right switch press changes current value Hold left switch again to exit clock set mode H 0.0 Hourmeter Right switch functions Pressing the right function switch during norma

Dakota Digital LED Tail Lights LAT-NR100

downloaded: 5File size: 168 kb    Manafacture: Dakota Digital  
Category: Work and Flash Light

Remove the tail light assembly from the vehicle by removing the original bulb sockets from the housing. Then remove the housing hardware so it can be removed from the car. Remove the housings from the vehicle carefully so the housing to body gaskets are not damaged. 2. Next remove the lens. The 67-68 Camaro has six screws that hold the housing halves together which will need to be removed to gain access to lens. The 70-73 Camaro lens has tabs locking it into the plastic housing. Pry the tabs gen

Dakota Digital LED Tail Lights LAT-NR230

downloaded: 4File size: 206 kb    Manafacture: Dakota Digital  
Category: Other Home Accessories

B Kit Includes: Installation: 1. Remove the two screws and tail light lens. 2. Remove the light bulb. 3. Push and twist to remove the plastic wire socket from the back side of the housing. 4. Now is a good time to clean the lens and housing. If lenses are in bad shape a new set is recommended. 5. Remove the nut and round metal spacer from the back of the new LED assembly. MAN#650188 rev. B 6. Insert the new LED assembly through the hole where the original bulb and connector were. Use caution whe

Dakota Digital LAT-NR261

downloaded: 4File size: 119 kb    Manafacture: Dakota Digital  
Category: Work and Flash Light

If the gasket is hard or brittle it should be replaced. 4. Now is a good time to clean or replace the lenses and housings if necessary. If the lenses are in poor condition a replacement set is recommended. MAN#650217 5. Insert the LED assembly bulb base into the tail light housing socket. 6. Place the new LED assembly into the housing so that the aluminum mounting bracket sits into the groove for the lens gasket. 7. Replace the lens gasket. The gasket will sit on top of the aluminum mountin

Dakota Digital LED Tail Lights LAT-NR101

downloaded: 4File size: 151 kb    Manafacture: Dakota Digital  
Category: Other Home Accessories

Remove the original bulb sockets from the housing. 2. Remove the tail light housing hardware so the housing can be taken out of the car. Remove the housings from the vehicle carefully so the body gaskets are not damaged. 3. Next remove the lens to gain access to the housing. There are six screws that hold the housing halves together, remove the screws and separate the halves carefully. 4. Now is a good time to clean the lens and housing. If lenses are in bad shape a new set is recommended. 5. Re





Category