Login:
Sorted: Name ↑   Downloads   Rate   Size ↑  

Omnimount UN-A-B

downloaded: 0File size: 211 kb    Manafacture: Omnimount  
Category: Projectors

Omnimount TILT-PA

downloaded: 8File size: 1017 kb    Manafacture: Omnimount  
Category: Projectors

TPUM-1: Tilting Pipe Adapter B. A. To adjust tilt 1. Hold A with 3/ 4” Socket 2. Loosen B with 3/ 4” Socket 3. Loosen C with 9/ 16” Socket 4. Position Display 5. Tighten A,B, & C • Designed for 26” - 55” Flat Panel • Maximum Weight Capacity: 175 • Connects to 1.5” NPT Pipe Specifications are subject to change without prior notice. Every effort has been made to provide accurate and error-free assembly and installation. Omni- Mount Systems disclaims liability for any difficulties arising from the

Omnimount PMD2

downloaded: 8File size: 353 kb    Manafacture: Omnimount  
Category: Projectors

Note: Orient the cable management port on the pipe drop assembly so that it faces the projector cable drop. Extended Ceiling Mount For installations that require a ceiling drop in excess of 18”, standard 1 .” pipe may be used to extend the standard pipe drop assembly. Pipe extension should be cut to the required additional length, threaded on both ends, and then attached to the standard pipe drop assembly with a pipe coupler (not supplied). Note: Orient the cable management port on the pipe drop

Omnimount PMD1

downloaded: 8File size: 353 kb    Manafacture: Omnimount  
Category: Projectors

6 Determine required mounting screw size ( 4, 5 or 6 mm) for projector. Note: Consult projectors owners’ manual for screw sizes and mounting holes. Lay projector on table with mounting surface face up. Place grid section of bottom projector mounting plate onto top of projector in desired mounting orientation (horizontal or vertical). (Fig. 6) Using a pencil or felt tipped pen, mark the locations of the projectors threaded inserts onto the grid for refer- Part Projector Mounting Hardware Qty. Bag

Omnimount PMD.5

downloaded: 13File size: 353 kb    Manafacture: Omnimount  
Category: Projectors

Every effort has been made to provide accurate and error- free assembly and installation. OmniMount Systems disclaims liability for any difficulties arising from the interpretation of information contained in these instructions. If OmniMount products are used for purposes other than their original intent, OmniMount, its distributors and retailers shall not be held responsible or liable for injuries or property damage, direct, indirect, or consequential, which may arise from the inability to use

Omnimount PMD Series

downloaded: 13File size: 172 kb    Manafacture: Omnimount  
Category: Projectors

Omnimount PMC-AL

downloaded: 4File size: 172 kb    Manafacture: Omnimount  
Category: Projectors

Omnimount PFC-A

downloaded: 28File size: 160 kb    Manafacture: Omnimount  
Category: Projectors

PFC-A (Female to Female Coupler) OMNI (Not Included) PFC Coupler 1 r 1 - fl V_!-■ <»-^P-A NPT pipes Available Sizes 12", 18", 24" (Not Included) (Not Included) Pouch # Part # Description Qty 1 COUPLER (PMD Series Compatible) 1 1 P-A SCREW 1/4 inch L 3/8 inch 4 1 P-B ALLEN KEY M4 1

Omnimount OM10131

downloaded: 9File size: 4 mb    Manafacture: Omnimount  
Category: Projectors

Omnimount L27-OM1100149-CON-021810vC

downloaded: 2File size: 13 mb    Manafacture: Omnimount  
Category: Televisions

USER MUST REMOVE TELEVISION OR OBJECT OFF THE BRACKET BEFORE ADJUSTING. IF THE PRODUCT IS A TELEVISION MAXIMUM WEIGHT CAPACITY SUPERSEDES / OUTPLACES RECOMMENDED DIAGONAL MEASURED TELEVISION SIZE!! EL USO CON EL PRODUCTOS MAS GRANDE QUE EL PESO MAXIMO Y TAMANO PUEDE CAUSAR INESTABILIDAD Y POSIBLEMENTE HERIDAS. EL USUARIO DEBE QUITAR LA TELEVISI ON U OBJETO DEL SOPORTE ANTES DEL AJUSTE. SI EL PRODUCTO ES UNA TELEVISI ON, LA CAPACIDAD DE PESO MAXIMA REEMPLAZA EL TAMANO DIAGONAL RECOMENDADO DE LA T





Category