Description Attachment 1695468 522E, 22" Single Stage Snow Thrower 1695514 522EX, 22" Single Stage Snow Thrower Not for Reproduction Rev. 11/2008 TP 400-5004-00-ST-S Part No.: 1737494 Not for Reproduction Table Of Contentss PRODUCT COMPONENTS PAGES Frame and Fuel Tank ........................................................................................................................................... 4 Engine Drive System .....................................................................

All rights reserved Decals NOTE: Unless noted otherwise, use the standard hardware torque specification chart. Not for The above parts group applies to the following Mfg. Nos.: 1695468 - 522E 1695514 - 522EX Briggs and Stratton Yard Power Products Group Copyright © 2008 by Briggs and Stratton Corporation 14 TP 400-5004-00-ST-S Milwaukee, WI, USA. All rights reserved Decals REF NO PART NO. QTY. DESCRIPTION 1 1736343YP 1 DECAL, Control Panel Electric Start (Domestic Only) 1 1740400MA 1 DECAL, Cont

However, we reserve the right to change, alter or otherwise improve the product and this document at any time without prior notice. Read the Operator’s Manual • Locate the operator’s manual in the manual packet. Always read and follow the instructions in the operator’s manual. Proper care, performance tips, and safety information are located in this important document. • “Right” and “Left” are from the Operating Position. Raise The Handles • Cut four orange zip ties (E, Figure 3) that secure con

TILLER MFG. NO. 1690322 CAUTION: Read Manual Thoroughly Before Operating FORM —1657962-02 PRINTED IN U.S.A. 774 GENERAL INTRODUCTION This Owner’s Guide has been prepared to provide the information needed to assemble and operate your tiller with greater satisfaction. Read this Owner’s Guide carefully. Be sure you know what the controls are for and how they operate. The care your tiller requires is small, but important. Keep it clean and well lubri- cated. With proper care and operation, as e

TILLER MFG. NO. 1690237 5 H.P. TILLER MFG. NO. 1690324 CAUTION: Read Manual Thoroughly Before Operating |Ç*FD R'M*^TdB3 f28£l { PRINTED IN U S A | Dear Customer, Congratulations on your selection and purchase of this walk-behind rotary tiller. It has been carefully designed and built to give you years of dependable service. With proper care, it will help you do your tilling jobs efficiently. To make sure you get the best use from your tiller, read this manual carefully. Make sure that your

TILLER MFG. NO. 1690238 CAUTION: Read Manual Thoroughly Before Operating FORM - 1657225 PRINTED IN U.S.A. 768 Dear Customer, Congratulations on your purchase of this walk behind rotary tiller. It has been carefully designed and built to give you years of dependable service. With proper care, it will help you do your tilling jobs efficiently. To make sure you get the best use from your tiller, study this manual carefully. Make sure that it is assembled properly, and that all adjustments are

N0.1600400 5HP TILLER MFG. NO. 1600407 TINE EXTENSION KIT MFG. NO. 1600373 FURROW OPENER -,^7'*’V.***-; <.v.\ -‘AVv, .• *• vf- v, ****•>'. 4 .1*i .. *•£»** FORM — 1609450 PRINTED IN U.S.A. 747 LIMITED WARRANTY New SIMPLICITY products sold by Simplicity Manufacturing Company are warranted by Allis-Chalmers Corporation (the Company) to be merchantable and free of defects in workmanship and material at the time of shipment from the Company’s factory. THERE ARE NO WARRANTIES WHICH EXTEND BE

Crank engine a few times to blow excess oil out of plug hole. Then reinstall the plug. 3. Fill fuel tank with fresh gasoline (unless a fuel stabilizer was used). 4. Start the engine outdoors. Do not run engine at high speeds immediately after starting. Check tiller and engine (5-hour care) 1. Check tiller and engine for loose screws, pins, bolts, oil leaks, etc. 2 Clean area around oil fill plug. NOTE Engine must be level. 3. Check/add engine oil as follows: A. Remove oil fill plug. B.

16 x 1" 4 720002 7 Lock Washer, 3/S" 5 717003 7 Hex Nut, Full 3/8"-16 6 107106 2 Shoe Assy. 7 719001 4 Flat Washer, 3/S” 8 720002 4 Lock Washer, 3/8" 9 705004 4 Hex. Cap Screw, 174054 S/8'J-16 x 3/4" 10 1 Pivot Frame Assy. 11 715100 2 Hex Capscrew, l/2”-13 x 1-1/2" 12 717518 2 Hex Nut, 1/2"* 13 13 107116 1 Pivot Plate Assy. 14 722006 2 Cotter Pin 1/8“ x 1" 15 107118 1 Pivot Rod 16 722001 2 Cotter Pin, 3/32” x 3/4" 17 107119 1 Pivot Arm id 156150 1 Spacer 19 705007 1 Hex Capsc

Place the pivot pin through the blade assembly bracket and push bar. Position the push bar under the tractor front axel and attach it to the axel using two pins and spring clips. Attach the spring end of the lift rod to the push bar assembly and the other end to the tractor lift arm using two spring clips. OPERATION Alternate holes are provided to permit adjustment of the shoe assemblies for raising or lowering the blade when cleaning gravel drives or walks. When cleaning concrete it is desira