• Verify that all suction lines are closed except the one utilized by the flow indicator. • Check hose cuffs and connections for leaks that cause loss of flow. • For dedicated suction line installations, adjust valve in equipment area that controls water flow to suction line until indicator is within the target area. Mark valves for reference. • For skimmer installations, turn knob on flow regulator clockwise until indicator is within the target area. If the indicator does not move into the targ
• After cleaning or backwashing, let the filtration system run for at least five minutes before re-connecting the Polaris. • New plumbing lines should be flushed out before installing the Polaris. • The Polaris should not be used to remove plaster dust in new pools. • Never handle the Polaris while it is operating. • When not in operation, always use the handle to pick up the cleaner. • Always remove the Polaris before swimmers enter the pool. • Always remove the Polaris from the pool before che
Technical tips . New product introductions . Event schedules . Parts and Service Manual information . Exciting details about The Way Out . Racing Information Check it out... All information in this manual is based on the latest product data and specifications available at the time of printing. Polaris Industries Inc. reserves the right to make product changes and improvements that may affect illustrations or explanations. No part of this manual shall be reproduced or used without the written per
Part # Description Qty No. Part # Description Qty No. Part # Description Qty 1 2 3 K16 C40 K5 All-Purpose Bag* 1 Screw, 10-32 x 3/8" SS Pan 20 Top 1 20 21 C10 C6 Tire, MaxTrax®* 3 Wheel, Large (No Bearings Incl.) 3 39 40 41 9-100-1018 10-112-00 6-500-00 Bag Collar 1 Restrictor Disks, Red and Blue 1 Universal Wall Fitting (UWF) 122 23 24 C65 C131 C16 Axle, Large (Rear Wheel Only) 1 Thrust Jet Kit 1 Idler Wheel, Small 1 4 5 6 A20 9-100-3105 B25 Float, Head 1 Sweep Hose Scrubber* 1 Orifice Tip w/Or
Contact an authorized Polaris dealer for more information. 45 ElbowVacuum Plate90 ElbowVacuum Plate StandardHoseVacuum PlateStandard Skimmer Deep Skimmer Shallow Skimmer Connecting the Hose 1. Set aside the leader hose with hose weight and standard hose with hose weight. 2. Connect remaining hose sections pushing cuffs securely together. 3. Attach standard hose with hose weight to end of hose. 4. Attach leader hose to same end. The leader hose connects to the Polaris. 5. Connect assembled hose t
Other connections are possible, but they require additional fittings (see Section B on page 4). The Polaris 380 is intended for use with a Polaris Booster Pump.You should have a licensed electrician install the cleaner’s booster pump. The booster pump must be installed according to the electrical codes applicable in your area. Improper installation can result in serious or even fatal injury. The following are important points to remember when installing and operating the Polaris 380. • Always tu
• Для установки времени, нажмите кнопку “Time“ и установите текущее время кнопками “up/down“ , значение часа в диапазоне от 0 до 23, затемминуты – от 0 до 59. • Для установки времени работы обогревателя нажмите кнопку “Clocked” Выберите время работы обогревателя с помощью кнопок “up/down“ . Обогреватель будет автоматически поддерживать выставленную температуру. По истечению выставленного времени обогреватель автоматически выключится. На дисплее будет отображено текущее время. 6 . Для отмены уста
Внимание. При выключении обогревателя при установленном таймере, значения установок таймера стираются из памяти. Рис559,6см При выключении обогревателя, он будет работать в режиме вентиляции для охлаждения нагревательных элементов в течение 30 секунд, после чего прибор отключатся автоматически, створки закроются. Управление прибором кнопками на обогревателе Кнопка «function» • При первом однократном нажатии на кнопку «function», вы услышите звуковой сигнал, загорится индикатор, включится вентиля