Login:
Sorted: Name ↓   Downloads   Rate   Size ↑  

JL Audio e1200

downloaded: 3File size: 201 kb    Manafacture: JL Audio  
Category: Car Amplifiers

INPUT SECTION The e1200 has one input section with two distinct input connection options. 1) A pair of traditional RCA type connections designed to accept input from source units with line level outputs. 2) A four-pin connector designed to accept input from amplified sources such as factory source units or source units not equipped with line level outputs. You may run a stereo or a mono signal into the inputs of the amplifier. The amplifier's input section automatically sums stereo signals to mo

JL Audio e1800D

downloaded: 6File size: 8 kb    Manafacture: JL Audio  
Category: Car Amplifiers

JL Audio e1800D

downloaded: 6File size: 8 kb    Manafacture: JL Audio  
Category: Car Amplifiers

JL Audio G4500

downloaded: 5File size: 8 kb    Manafacture: JL Audio  
Category: Car Amplifiers

JL Audio G4500

downloaded: 11File size: 8 kb    Manafacture: JL Audio  
Category: Car Amplifiers

JL Audio HD900/5

downloaded: 4File size: 1 mb    Manafacture: JL Audio  
Category: Car Amplifiers

Your amplifier has been designed and manufactured to exacting standards in order to ensure years of musical enjoyment in your vehicle. For maximum performance, we highly recommend that you have your new amplifier installed by an authorized JL Audio dealer. Your authorized dealer has the training, expertise and installation equipment to ensure optimum performance from this product. Should you decide to install the amplifier yourself, please take the time to read this manual thoroughly so as to fa

JL Audio J21000.1

downloaded: 1File size: 285 kb    Manafacture: JL Audio  
Category: Car Amplifiers

LP F Rotating the control clockwise will result in higher sensitivity (louder for a given input voltage). Rotating the control counter-clockwise will result in lower sensitivity (quieter for a given input voltage). To properly set the amplifier for maximum clean output, please refer to Appendix A (page 12) in this manual. After using this procedure, you can then adjust the level of the amplifier by adjusting the input sensitivity downward, if the amplifier requires attenuation to achieve the des

JL Audio J2250.1

downloaded: 3File size: 316 kb    Manafacture: JL Audio  
Category: Car Amplifiers

For optimum cooling performance, this outer shell should be exposed to as large a volume of air as possible. Enclosing the amplifier in a small, poorly ventilated chamber can lead to excessive heat build-up and degraded performance. If an installation calls for an enclosure around the amplifier, we recommend that this enclosure be ventilated with the aid of a fan. In normal applications, fan-cooling is not necessary. Speaker Outputs (pg. 10) Speaker Output (Mono) IMPORTANT! Mounting the amplifie

JL Audio J2320.4

downloaded: 5File size: 368 kb    Manafacture: JL Audio  
Category: Car Amplifiers

“My amplifier doesn’t turn on” Check the fuse, not just visually, but with a continuity meter. It is possible for a fuse to have poor internal connections that cannot be found by visual inspection. It is best to take the fuse out of the holder for testing. If no problem is found with the fuse, inspect the fuse-holder. Check the integrity of the connections made to each of the “+12VDC”, “Ground”, and “Remote” terminals. Ensure that no wire insulation is pinched by the terminal set screw and that

JL Audio J2360.2

downloaded: 1File size: 310 kb    Manafacture: JL Audio  
Category: Car Amplifiers

To connect the remote turn-on wire to the amplifier, strip 1/2-inch (12 mm) of insulation from the wire and insert it into the “Remote” receptacle on the power connector. Tighten the connector down using a Phillips screwdriver. inPut seCtions The J2-360.2’s has one pair of stereo inputs.The input section input section offers two input connection methods, one for high-level (speaker level) signals and one for low-level (preamp level) signals. 1) Low-Level Inputs: A standard left/ right pair of RC





Category