MAKE WORKSHOP KID PROOF 6. with padlocks, master switches, or by removing starter keys. DON’T FORCE TOOL. It will do the 7. job better and safer at the rate for which it was designed. USE RIGHT TOOL. Don’t force tool 8. or attachment to do a job for which it was not designed. RECOMMENDED MINIMUM WIRE GAUGE FOR EXTENSION CORDS (120 VOLT) NAMEPLATE AMPERES (at full load) EXTENSION CORD LENGTH 25’ 50’ 100’ 150’ 0 – 6 18 16 16 14 6.1 – 10 18 16 14 12 10.1 – 12 16 16 14 12 12.1 – 16 14 12 Do not use.

Additionally, read all of the warnings and instructions provided in the instruction manual of the air compressor you will be using. WARNING: This product contains or, when used, produces a chemical known to the State of California to cause cancer and birth defects or other reproductive harm. (California Health & Safety Code 25249.5, et seq.) Unpacking When unpacking, check to make sure the parts listed on page 8 are included. If any parts are missing or broken, please call Harbor Freight Tools a

Otherwise, the extension cord could melt and catch fire, or cause electrical damage to the tool. Check your compressor’s manual for the appropriate size cord. 19. Maintenance. For your safety, maintenance should be performed regularly by a qualified technician. 20. Compressed air only. Never use combustible gases as a power source. 21. Continual exposure to sound levels above 85 decibles could cause hearing damage. Hearing protection is advised with this tool. Note: Performance of the compressor

If there is any doubt, do not operate the tool. 18. Pacemaker safety warning. People with pacemakers should consult with their physician(s) before using this product; operation of equipment in close proximity to a heart pacemaker could cause interference or failure of the pacemaker. 19. Use proper size and type extension cord. If an extension cord is required, it must be of the proper size and type to supply the correct current to the tool without heating up. Otherwise, the extension cord could

When servicing, use only identical replacement parts. Use of any other parts will void the warranty. Only use accessories intended for use with this product. 11. Do not operate if under the influence of alcohol or drugs. Read warning labels on prescriptions to determine if your judgment or reflexes are impaired while taking drugs. If there is any doubt, do not operate the product. 12. Maintenance. For your safety, service and maintenance should be performed regularly by a qualified technician. S

If eye contact is made, flush the eyes with running cold water for ten minutes and then immediately get medical attention. Fire Hazards 1. Use of attachments not designed for this specific model may cause a fire. 2. Disassembling the battery charger may cause a fire. Always have a qualified service technician work on the battery charger. 3. Arcing flames and sparks are possible if you plug in the battery charger before connecting to the battery. Always unplug the charger before battery hookup. M

Arc Welding Safety Warnings and Precautions Warning:This product, when used for welding and similar applications, produces chemicals known to the State of California to cause cancer and birth defects (or other reproductive harm). California Health & Safety Code 25249.5, et seq. 1. Avoid electrical shock. Do not permit electrically live parts, cables, or electrodes to contact skin, clothing, or gloves. Protective clothing should be free of holes, dry, and ANSI approved. This unit draws enough cur

Tools marked “Double Insulated” do not require grounding. They have a special double insulation system which satisfies OSHA requirements and complies with the applicable standards of Underwriters Laboratories, Inc., the Canadian Standard Association, and the National Electrical Code. (See Figure B.) 5. Double insulated tools may be used in either of the 120 volt outlets shown in the following illustration. (See Figure B.) FIGURE B SKU 03670 PAGE 7 EXTENSION CORDS 1. Grounded tools require a thre

For future reference, please complete the owner’s record below: Model___________ Serial No._____________ Purchase Date_____________ Save This Manual You will need the manual for the safety warnings and precautions, assembly instructions, operating and maintenance procedures, parts list and diagram. Keep your invoice with this manual. Write the invoice number on the inside of the front cover. Keep the manual and invoice in a safe and dry place for future reference. Technical Specifications Produc