Cooktop sides lay directly on edge of countertop. Formed front-edged countertops must have molded edge shaved flat 3/4" from each front corner of opening. Tile countertops may need trim cut back 3/4" from each front corner and/or rounded edge flattened. If the existing cutout width is greater than 30 1/16", reduce the 3/4" dimension. Grounded Junction Box in adjoining cabinet Do not pinch the power supply cord between the range and the wall. Do not seal the range to the side cabinets. *No
You will not be able to see that the burner is on. Burns will occur if the hot covers are touched. Damage may also be done to the cooktop or burners because the covers may cause overheating. Air will be blocked from the burner and cause combustion problems. IMPORTANT SAFETY NOTICE The California Safe Drinking Water and Toxic Enforcement Act requires the Governor of California to publish a list of substances known to the state to cause cancer, birth defects or other reproductive harm, and require
They should never be allowed to sit or stand on any part of the appliance. Sears Parts & Repair is the recommended repair service for this appliance. Know how to disconnect the electrical DO NOT TOUCH SURFACE BURNERS, GRATES, OR power to the appliance at the circuit breaker or fuse box in AREAS NEAR THESE BURNERS. Surface burners may case of an emergency. be hot even though the flames are not visible. Areas near surface burners may become hot enough to cause burns. ,, User Servicing--Do not repa
However, only the selected surface Burner will lite. 4. Visually check that zone A & B of the dual burner has lit. 7. When both zones are lit, continue to turn the control knob counterclockwise between dual Hi & LO to adjust to the desired flame size for both burners together. Note: The markings between the Dual Hi and LO settings on the control knob adjust the flame size for both zone A & B (Refer to Figure 2 or 3). DO NOT cook with any of the surface control knobs in the LITE position (The ele
Surface Control knob has not been completely turned to LITE. Push in and turn the Surface Control knob to LITE until burner ignites and then turn control to desired flame size. Be sure gas supply valve is open. Gas-air mixture needs a straight line to travel. Be sure burner is properly seated in its support (models with open burners only). Burner ports or slots are clogged. With the burner off, use a small-gauge wire or needle to clean ports or slots. Power cord is disconnected from outlet (elec
Surface Control knob has not been completely turned to LITE. Push in and turn the Surface Control knob to LITE until burner ignites and then turn control to desired flame size. Be sure gas supply valve is open. Gas-air mixture needs a straight line to travel. Be sure burner is properly seated in its support (models with open burners only). Burner ports or slots are clogged. With the burner off, use a small-gauge wire or needle to clean ports or slots. Power cord is disconnected from outlet (elec
Never Leave Surface Burners Unattended at High Heat Settings--Boilovers cause smoking and greasy spillovers that may ignite, or a pan that has boiled dry may melt. Protective Liners--Do not use aluminum foil to line surface burner pans. Protective liners or aluminum foil may interfere with heat and air distribution, and combustion. Damage to the cooktop or personal injury may result. Glazed Cooking Utensils--Only certain types of glass, glass/ceramic, ceramic, earthenware, or other glazed utensi
5. Damage to or failure of this product resulting from accident, abuse, misuse or use for other than its intended purpose. 6. Damage to or failure of this product caused by the use of detergents, cleaners, chemicals or utensils other than those recommended in all instructions supplied with the product. 7. Damage to or failure of parts or systems resulting from unauthorized modifications made to this product. Disclaimer of implied warranties; limitation of remedies Customer's sole and exclusive r
To Clean the Removable Burner Base and Gas Opening (some models) The ports (or slots) around the burner base must be routinely cleaned. Use a small-gauge wire or needle to clean small slots or holes. Note: If the electrode is damaged or broken, the surface burner will not light because it will not spark. Manual lighting with a match is still possible. For proper flow of gas and ignition of the burner -DO NOT ALLOW SPILLS, FOOD, CLEANING AGENTS OR ANY OTHER MATERIAL TO ENTER THE GAS OPENING TUBE.
Para solicitar precios e informacibn adicional, Ilame al 1-800-827-6655 (en los EE.UU.). * La cobertura en Canadb varia en el caso de algunos articulos. Para obtener detalles completos al respecto, Ilame al 1-800-361-6665 de Sears de Canadb. Servicio de instalaci6n de Sears Para solicitar la instalaci6n por profesionales de Sears de electrodom6sticos, abridores de puertas de garaje, calentadores de agua y otros articulos de uso prioritario en el hogar, Ilame al 1-800-4-MY-HOME en los EE.UU. o Ca