2 ©2004, 2005 Fluke Corporation, All rights reserved. Printed in U.S.A. All product names are trademarks of their respective companies Fluke Biomedical Radiation Management Services 6045 Cochran Road Cleveland, Ohio 44139 440.498.2564 Table of Contents Section 1: General Information................................................................................... 1-1 1.1 Introduction .................................................................................................. 1-1 1.2 Descr

All rights reserved. FLUKE 1652C/1653B/1654B Users Manual Supplement Change #1, 56800 On page 3, add the following bullet: • Do not use in CAT III or CAT IV environments without the protective cap installed. The protective cap decreases the possibility of arc flash caused by short circuits. On page 6, under Operating the Tester Using the Rotary Switch, add the following: WWarning Do not use in CAT III or CAT IV environments without the protective cap installed. The protective cap decrea

This manual is distributed as an electronic manual on the following CD-ROM: CD Title: 1652C/1653B/1654B CD Rev. & Date: 9/2010 CD PN: 3798444 © 2010 Fluke Corporation. All rights reserved. FLUKE 1652C/1653B/1654B Users Manual Supplement Change #1, 56800 On page 3, add the following bullet: • Do not use in CAT III or CAT IV environments without the protective cap installed. The protective cap decreases the possibility of arc flash caused by short circuits. On page 6, under Operating th

The protective cap decreases the exposed probe metal to <4mm. This decreases the possibility of arc flash from short circuits. On page 45, under General Specifications, add the following to the Safety section: Complies with EN/IEC 61010-031:2002+A1:2008. 12/10 1

This would be the connection at a branch circuit. Power Recorder Power Type Diagrams SD ETHERNET POWER 1750 POWER RECORDER ON BUSY LINK 100-240 V 47-63Hz BA C N VOLTAGE CURRENT A/L1 NGND B/L2 azd03f.eps Figure 6. One-Phase Split Phase Example: A North American residential installation at the service entrance. Operators Manual SD ETHERNET POWER 1750 POWER RECORDER ON BUSY LINK 100-240 V 47-63Hz BA C N VOLTAGE CURRENT B/L2 A/L1 C/L3 NGNDSource GND OC/L3 OA/L1 OB/L2 azd04f.eps Figure 7. Three-Phase

• Be sure the test leads and switch are in the correct position for the desired measurement. • Never measure resistance in a circuit when power is applied. • Never touch the probes to a voltage source when the test leads are plugged into the 10 A or 300 mA input jack. • Never apply more than the rated voltage between any input jack and earth ground. • Be careful when working with voltages above 60 V dc or 30 V ac rms. Such voltages pose a shock hazard. • Keep your fingers behind the finger guard

RANGE CAT CAT + _ hc7f.eps Diode Test (G) RANGE CAT + _ _ Forward Bias Single Beep RANGE CAT CAT + Reverse Bias _ RANGE CAT CAT + Shorted Open and Good Diode Good Diode Bad Diode _ RANGE CAT CAT + Bad Diode hc5f.eps Continuity Test ( R ) RANGE CAT CAT + _ RANGE CAT CAT + _ hc8f.eps If continuity exists (resistance < 210 W for Models 21/75 and <270 W for Models 23/77), the beeper sounds continuously. The meter beeps twice if it is in Touch Holda mode. Current(?A) W Warning To avoid injury, do not

10 ©2004, 2005 Fluke Corporation, All rights reserved. Printed in U.S.A. All product names are trademarks of their respective companies Fluke Biomedical Radiation Management Services 6045 Cochran Road Cleveland, Ohio 44139 440.498.2564 120 Andrews Road Hicksville, New York 11801 516.870.0100 Table of Contents Section 1: General Information................................................................................... 1-1 1.1 Introduction ......................................................

Offset may be applied to the output to shift the signal either positive or negative. Offset and amplitude are inter-related, so make sure you understand the offset-amplitude ranges before you apply offset to your signal. A special fine offset generator is built into each channel, which allows programming of extremely small offset increments. This feature extends the offset resolution to 6 digits and is very useful in applications such as mixer balancing where few micro-volts could sway the balan

The second alternative is to use ArbExplorer for high-level programming. ArbExplorer is a software package supplied with the Instrument that simulates a set of mechanical front panels. It has all the necessary push buttons, displays and dials to operate the Instrument as if you were using it on the bench. The third alternative is using application specific drivers, such LabVIEW or IVI. The Instrument must be programmed to generate waveforms. Therefore, it is recommended that the user becomes fam