1.1 [08/06] CAC CASSETTE HIGH EFFICIENCY EVAPORATOR INSTALLATION, OPERATION AND MAINTENANCE MANUAL P/N 240006022, Rev. 1.1 [08/06] This manual is intended as an aid to a qualified service personnel for proper installation, operation, and maintenance of EMI AmericaSeries high efficiency evaporators. Carefully read these instructions before attempting installation or operation. Failure to follow these instructions may result in improper installation, operation, service, or maintenance, possibly re

Key features include a condensate pump with safety switch and an 30” lift; electric heat; fresh air inlet and branch duct knockouts; and motorized air vanes (18-36 only). the caf accepts a 24 volt thermostat control (thermostat not included) or an infrared microprocessor control can be obtained as a factory installed option. Hot water coils are available on all CAF models (except for 12,000 Btu) in place of electric heat. Due to ongoing product development, all designs and specifications are sub

The heating capacity at 70. F indoor and17. F outdoor shall be 5,300 Btuh. PART FOUR “INDOOR UNIT” The indoor unit shall be factory assembled, wired and contain a low voltage transformer. The cabinet shall be fabricated of G60 galvannealed steel, finished in “off-white” with corrosion inhibiting polyester powder-coated paint. The evaporator fans shall be a forward curve centrifugal type, dynamically balanced and directly mounted to the motor shafts. The motor shall be PSC type with internal ther

The S1C/S1H system can be recommended for both commercial and residential use. S1C/S1H 9-24 and S1C 30-36 SIN GLE ZONE Ductless Split Condensing Unit P/N 240005841, Rev. A [05/08] Low Ambient cooling operation down to 32. F are standard on all S1H (heat pumps) factory installed (optional on S1Cs) • Low Ambient cooling operation down to 32. F – Specify this option if the S1C system will be operated in cooling mode at outside temperatures below 60. F (field installed kit) • Low Ambient controls fo

Design and specifications may change without notice. System performance data: matched with emi AmericaSeries indoor units S1C eleCtriCAl SpeCiFiCAtiOnS model # Volts/HZ/pH Fan motor Compressor total AmpS min Volt m.C.A. HACr BrKr AmpS Hp rlA lrA S1C9A 115/60/1 1.4 0.125 6.7 29.0 8.1 104 9.8 15 S1C2A 115/60/1 1.4 0.125 8.4 44.0 9.8 104 11.9 20 S1C9D 208/230/60/1 0.8 0.125 3.5 19.0 4.3 197 5.2 15 S1C2D 208/230/60/1 0.8 0.125 4.5 21.0 5.3 197 6.4 15 S1C8D 208/230/60/1 0.8 0.125 5.4 36.0 6.2 197 7.6

1.1 [12/04] EMI ENGINEERING SUBMITTAL CAPACITIES: Cooling 33,000 Btu Heating – High 31,000 Btu – Low 18,200 Btu Indoor Design Temp .F DB/WB Cooling 80/67Heating 70/57 Outdoor Design Temp .F DB/WB Cooling 95/75Heating – High 47/43 – Low 17/15 EER 10.0 SEER 10.0 HSPF 6.8 17 ” 111/4 ” 571/2 ” INDOOR UNIT: Power Supply 208/230/1/60 Max. Fuse Size 15 Amps (w/o electric heat) Min. Ampacity .70 Amps (w/o electric heat) Max. Fuse Size 30 Amps (w/5kw electric heat) Min. Ampacity 27.9 Amps (w/5kw electric

or Distributor however the trap should be shallow as the: (4) elbow configuration. Each elbow is approximately 2 equivalent feet. One P-trap is equal to approximately 8 equivalent feet. P-TRAP INSTALLATION Figure #1 8Multi-zone Heat Pump Condensing Units REFRIGERANT PIPING INSTALLATION SECTION 9Multi-zone Heat Pump Condensing Units Vaccum Pump Micron Gage Manifold Setup For Evacuation S1CAShownIt is illegal to discharge refrigerant into the atmosphere. Use proper reclaiming methods & equipment w

A [06/08] • Cabinet (available in designer white with grey discharge vanes) fabricated of cold roll steel with structural stiff- The WCP is a contemporary design, chilled water air handler that combines attractive appearance in any decor, with the highly efficient conditioning of small to mid size commercial or residential spaces. Equipped with unit mounted infrared compatible controls, optional hand held remote also available. Units provide up to a nominal 30,000 Btuh of cooling. Electric heat

Optional hand held remote is available. Heat Pump models provide up to a nominal 24,000 Btuh of cooling and heating. Electric heat options are available for up to 5KW of supplemental heat. This American-made evaporator offers ease of installation, operation, and service. It can be matched with EMI’s S1C/S1H 09-24 and S1C 30-36 Btuh Single-Zone Condensing Units, the S2C side discharge Multi-Zone Condensing Unit, or the T2C, T3C, and T4C top discharge Multi-Zone Condensing Units. Unit Mounted Cont

When the “PROG” and “TIME” buttons are pressed simultaneously again or left idle for 20 seconds, the control shall save the new settings and return to the previous interface mode. While in the 7-Day programming mode, use the up or down arrows to change the time, temperature or period settings. Use the “MODE” (BACK) or “PROG” (NEXT) buttons to select the mode to be changed. Settings for (1) Day of week, (2) Period of day, (3) Hour, (4), Minute, (5) Cool setpoint temperature, (6) Heat setpoint tem