Login:
Sorted: Name ↓   Downloads   Rate   Size ↑  

Closet Maid 2-Door Versa Cabinet 12075

downloaded: 0File size: 7 mb    Manafacture: Closet Maid  
Category: Other Home Accessories

INST. # 59349 REV. 4/05 GENERAL HELPFUL HINTS (May vary according to product pur chased) COUNT HARDWARE Before assembly, identify and count all hardware parts, then group identical parts together for easier assembly. To help you identify the correct screw styles and sizes, each screw has been illustrated in the following steps. UNIT ASSEMBLY Assemble your unit on the carton it was packed in. For maximum work area, lay the carton out flat. This will protect your unit's finish during assembly and

Closet Maid 2-Drawer Kit 3775

downloaded: 2File size: 228 kb    Manafacture: Closet Maid  
Category: Other Home Accessories

Abra el cajon y coloque la funda de plastico (incluida) dentro del cajon. Repita los pasos 2, 3 y 4 para el otro cajon. © ClosetMaid Corporation 2006 Ocala, FL 34478-4400 1-800-874-0008 (USA, Canada) Importer in Mexico Importateur au Mexique Importador en Mexico Emerson Electric de Mexico, S.A. de C.V. Camino a Santa Monica 238 Vista Hermosa 54080, Tlalnepantla Estado de Mexico Phone (55) 5366-6180 Fax (55) 5366-6182 RFC EEM 940721 SH7 USE AND CARE: Use drawer to store items. Additional drawers

Closet Maid 2-Drawer Kit 93775

downloaded: 4File size: 228 kb    Manafacture: Closet Maid  
Category: Other Home Accessories

4 4. Secure standards to wall (see instructions provided with standards). Slide supplied drawer into lower channels on each bracket. Open drawer and place plastic insert (supplied) inside drawer. Repeat steps 2,3, and 4 for remaining drawer. 4 . Fixer les rails verticaux au mur (consultez les instructions fournies avec les rails verticaux). Faites glisser le tiroir fourni dans les glissiere s i n f e r i e u res de chaque support. Ouvrir le tiroir et placer la section de plastique (fournie) a l’

Closet Maid 2894

downloaded: 10File size: 367 kb    Manafacture: Closet Maid  
Category: Other Home Accessories

(See Parts List below.) 2. Please read all instructions carefully before beginning. Antes de empezar 1. Remueva el producto del paquete y cuidadosamente inspeccione todas las partes. (Vea la lista de partes abajo). 2. Haga el favor de leer todas las instrucciones cuidadosamente antes de empezar. Parts List a. Repisas de Close Mesh de 1,22 cm (4) 02-4318 b. Rieles Verticales de 1,22 m (3) 01-28044 c. Soportes de Repisa (12) 02-42854 d. Riel Horizontal de 1 m (1) 01-28266 e. Tapones para Repisa (3

Closet Maid 3-Cube Storage System 8178

downloaded: 0File size: 158 kb    Manafacture: Closet Maid  
Category: Other Home Accessories

Ensamble las rejillas usando los conectores. Asegúrese de encajar las rejillas de la parte inferior y lateral en las aperturas en forma de cruz en el conector. Encaje la rejilla trasera en la apertura lateral del conector (en el borde). Vea el recuadro. Consejos prácticos: • Use esta secuencia para instalar cada nivel de rejilla: 1) parte inferior 2) lado 3) parte trasera. • Para la segunda y tercera fila de cajas, instale los conectores traseros SÓLO antes de instalar las rejillas inferior,

Closet Maid 6-Cube Storage System

downloaded: 1File size: 223 kb    Manafacture: Closet Maid  
Category: Other Home Accessories

Encaje la rejilla trasera en la apertura lateral del conector (en el borde). Vea el recuadro. Consejos prácticos: • Use esta secuencia para instalar cada nivel de rejilla: 1) parte inferior 2) lado 3) parte trasera. • Para la segunda y tercera fila de cajas, instale los conectores traseros SÓLO antes de instalar las rejillas inferior, lateral y trasera. Después, instale los conectores delanteros. • Use un mazo de goma durante el ensamblaje para apretar todos los conectores. Alternate Assemb

Closet Maid 8-in-1 Closet Organizer 2890

downloaded: 0File size: 856 kb    Manafacture: Closet Maid  
Category: Other Home Accessories

See "STEP 2 - Shelf Design Options." Note: There are four 5' shelves supplied. If necessary, cut shelves with a hacksaw or boltcutter in one inch increments. We recommend cutting shelf from end that will be closest to side wall. b. Place shelf caps onto exposed shelf wires. c. Rest shelf on each shelf bracket at desired location. Pull shelf forward and allow front to “drop” over nose of shelf brackets (nose of each shelf bracket will fit between wires). Push shelf backwards so back wire fits int

Closet Maid Fabric Drawer 00467

downloaded: 11File size: 862 kb    Manafacture: Closet Maid  
Category: Dryers

252-6539 Manufacturer reserves the right to change specifications without notice. Le fabricant se réserve le droit de modifier les données techniques sans préavis. El fabricante se reserva el derecho a cambiar i ■ i ri-TgT.T-T-i | rWTiT las especificaciones sin previo aviso. Made in China / Fabriqué aux Chine / Hecho en China ©Stack A Shelf, 2006 089066004672

Closet Maid In-Cabinet Trash Pull-Out 3185

downloaded: 12File size: 308 kb    Manafacture: Closet Maid  
Category: Dryers

10 x 1,6 cm Tornillo #10 x 1,6 cm Please read all instructions carefully before beginning. Veuillez lire les instructions avec attention avant de commencer. Lea todas las instrucciones cuidadosamente antes de empezar. 1 2 3 4 5 REQUIRED TOOLS OUTILS REQUIS HERRAMIENTAS REQUERIDAS Part Piece Pieza Quantity Quantite Cantidad Part # Piece n. Pieza # Part Name Nom de Piece Nombre de la Pieza Emerson Electric de Mexico, S.A. de C.V. Camino a Santa Monica 238 Vista Hermosa 54080, Tlalnepantla Estado d

Closet Maid Large Trash Bag Holder 3024

downloaded: 0File size: 462 kb    Manafacture: Closet Maid  
Category: Other Kitchen Appliances

SIDE PANEL PANNEAU LATERAL PANEL LATERAL Square up end panels and push top hooks over top wire on end panels as shown (see top inset drawing). Position bottom wire of side panel between two end wires of end panel and sqeeze center wires while pushing into holes in assembling frame. Repeat steps to assemble opposite side panel. 4. Position mounting frame inside cabinet as shown. Be sure frame is straight to ensure smooth operation of trash bag holder. Position front mounting rail back 1-3/4" from





Category