(Ref. OSHA 1910.95 for occupational noise exposure guidelines) SA400 SA400SA400 RADIO RADIORADIO SIREN SIRENSIREN PA PAPA HORN HORNHORN VOL VOLVOL MAN MANMANWAIL WAILWAILYELP YELPYELP ON ONON OFF OFFOFF PHASER PHASERPHASER The OFF/ON Toggle Power Switch controls the siren power. The siren may be left on any time the vehicle is in operation. The power should be turned off when vehicle is not being used to conserve battery power. The Rotary Function Switch selects various operating modes. These mo

Carson MANUFACTURING COMPANY, INC. CARSON MANUFACTURING CO., INC. 5451 NORTH RURAL STREET INDIANAPOLIS, IN 46220 (888) 577 6877 TECHNICAL BULLETIN SA400 SA400SA400 RADIO RADIORADIO SIREN SIRENSIREN PA PAPA HORN HORNHORN VOL VOLVOL MAN MANMANWAIL WAILWAILYELP YELPYELP ON ONON OFF OFFOFF PHASER PHASERPHASER INSTALLATION AND OPERATING MANUAL SA-400-83 14V SA-400-83 28V SA-400-83 PG (Positive GND) Sound Hazard -Sound level from siren speaker (>120dBA @ 10 feet) may cause hearing damage. Do not opera

RADIO VOLUME ADJUST The RADIO VOLUME ADJUST is a one time setting which depends on the radio connected and its normal volume. The siren cover must be removed to access the adjustment. The cover is held in place by a snap-fastener on the back of the unit. While holding the case on the sides press hard with your thumbs on the back of the unit. The chassis will slide out the front. Switch siren to RADIO mode and turn on the power. With the volume on the radio itself set to normal level, set the RAD

Sound Hazard - Sound level from siren speaker (>120dBA @ 10 feet) may cause hearing damage. Do not operate siren without adequate hearing protection for you and anyone in immediate vicinity. (Ref. OSHA 1910.95 for occupational noise exposure guidelines) Page 2 of 16 SA-430-17 Installation and Operating Instructions TABLE OF CONTENTS TABLE OF CONTENTS.............................................................................................................2 SPECIFICATIONS ......................

If the amplifier needs service the connector can be easily removed without unwiring the harness. The power supply for the amplifier must be capable of delivering peak currents up to 50 amps for adequate short circuit protection and reliable operation. The preferred source is directly at the vehicle battery. A fuse on the unit protects from overload. Wire Size and Termination -The diagram shows the minimum wire size used for each connection. If the wire is longer than 10 ft. use the next larger w

Mounting the amplifier in the engine compartment or in an area directly exposed to weather is not recommended. Assure adequate ventilation to prevent overheating. Consider wire routing and access to connector. Install amplifier to vehicle using 1/4" hardware (not supplied). May need to set RADIO VOLUME ADJUST on side of amplifier before final mounting and installation. May also need to set POWER OUTPUT ADJUSTMENT on inside of amplifier. CONTROL HEAD MOUNTING Select a mounting location in an area

CARSON MANUFACTURING CO., INC. 5451 NORTH RURAL STREET INDIANAPOLIS, IN 46220 (888) 577 6877 TECHNICAL BULLETIN SA 441SA 441 RADIORADIO HRN/TTHRN/TT MANMAN WAILWAIL YELPYELP PHASR/WPHASR/W--YY SIRENSIREN PA VOL POWERPOWER OFF/ON ON INSTALLATION AND OPERATING MANUAL SA-441-83F (FLUSH MOUNT CONTROL HEAD) SA-441-83FX (FLUSH MOUNT WITH EXTENDED MIC) Sound Hazard -Sound level from siren speaker (>120dBA @ 10 feet) may cause hearing damage. Do not operate siren without adequate hearing protection for

The siren tone is controlled manually with SIREN button. Both speakers produce manual tone slightly out of phase to give stereo effect. PA Override available in this mode. WAIL -The siren produces dual Wail. Each speaker produces independent Wail tone. Dual Yelp and PA Override available in this mode. YELP -The siren produces dual Yelp. Each speaker produces independent Yelp tone. Phaser and PA Override available in this mode. WAIL/YELP -The siren produces Wail to one speaker and Yelp to the oth

Wiring -Use wiring capable of handling the current required. Make sure all connections are tight. Route wiring to prevent wear, overheating and interference with air bag deployment. Install and check all wiring before connection to vehicle battery. Testing - Test all siren functions after installation to assure proper operation. Test vehicle operation to assure no damage to vehicle. Keep These Instructions -Keep these instructions in the vehicle or other safe place for future reference. Advise t

The adjacent diagram shows three connection examples. See the INSTALLERSELECTABLE OPTIONS section for programming details. NOTE: Permanent disconnection of the vehicle horn is NOT recommended. tone output when activated, and remains off until examples. for programming details. TB0352A Page 5 of 8 09/27/05 OPERATION Sound Hazard - Sound level from siren speaker (>120dBA @ 10 feet) may cause hearing damage. Do not operate siren without adequate hearing protection for you and anyone in immediate vi