The 113A has been designed utilizing Bryant’s Puron refrigerant. The environmentally sound refrigerant allows you to make a responsible decision in the protection of the earth’s ozone layer. As an Energy Starr Partner, Bryant Heating and Cooling has determined that this product meets the Energy Starr guidelines for energy efficiency. Refer to the combination ratings in the Product Data for system combinations that meet Energy Starr guidelines. NOTE: Ratings contained in this document are subject
The qualified installer or agency must use factory- --authorized kits or accessories when modifying this product. Refer to the individual instructions packaged with the kits or accessories when installing. Follow all safety codes. Wear safety glasses, protective clothing, and work gloves. Use quenching cloth for brazing operations. Have fire extinguisher available. Read these instructions thoroughly and follow all warnings or cautions included in literature and attached to the unit. Consult loca
The 165A has been designed utilizing Bryant’s Puron refrigerant. The environmentally sound refrigerant allows you to make a responsible decision in the protection of the earth’s ozone layer. As an Energy Star ® Partner, Bryant Heating & Cooling has determined that this product meets the Energy Star® guidelines for energy efficiency. Refer to the combination ratings in the Product Data for system combinations that meet Energy Star® guidelines. NOTE: Ratings contained in this document are subjec
ALWAYS KEEP MAIN OIL VALVE TURNED OFF IF BURNER IS SHUT DOWN FOR AN EXTENDED PERIOD OF TIME. PERFORMING ROUTINE MAINTENANCE With proper maintenance and care, your furnace will operate economically and dependably. Instructions for basic maintenance follow. However, before beginning maintenance, follow these safety precautions: WARNING ! Turn off all electrical power to furnace before performing any maintenance or service on unit. Failure to take this precaution may result in personal injury due t
0 – March 2002 Text Box: WARRANTY Bacharach, Inc. warrants to Buyer that at the time of delivery this Product will be free from defects in material and manufacture and will conform substantially to Bacharach Inc.’s applicable specifications. Bacharach’s liability and Buyer’s remedy under this warranty are limited to the repair or replacement, at Bacharach’s option, of this Product or parts thereof returned to Seller at the factory of manufacture and shown to Bacharach Inc.’s reasonable satisfact
317 240 5662 Installation Ins GAS-FIRED WATER OR STEAi'1 30ÎLER Cancels: 39234D23 NOTE: THESE INSTRUCTIONS MUST BE LEFT ON OR NEAR THE BOILER. The Model 234 is a low-pressure» sectional, cast-iron water and steam boiler. The design is certified by A.G.A. for use with natural, and propane gases. It is tested for a maximum working pressure of 100 psi on water and 15 psi on steam in accordance with ASME standards for cast-iron boilers. The boiler is available as a Type GW ■ Gravity, Type PW -
This air must be : supplied through two openings of equal area; 'one ¡located above draft diverter relief opening and .other near floor.. Total free area of each openiiig should be equal to 1 square inch for, each 1,0.00 Btuhof boiler input. There should be a minimum of 100 square inches ¡for each opening. If air openings are directly to outdoors, minimum free area should be 1 square inch per 2,000 Btu .per hour of input rating, or in accordance with ANSIZ21.30 or the latest edition of “American
Type “S” for steam can be used in systems with a maximum work“ ing pressure of 15 psig. Type fiW” for water can be used in systems with a maximum working pressure of 50 psig. Installer; The boiler is shipped knocked down. Check rating piate for type of gas, input, voltage) etc,, to be sure that all equipment furnished meets the requirements of the installation. Read these instructions completely before beginning the installation. On the end of manifold fitting box there is a master copy of all
The design is certified by' the American Gas Association for use with natural or propane gas. The typé S boiler can be used in steam systems with a maximum working pressure of 15 psig. The type W boiler can be used in water systems with a normal working pressure of 30 psig and is available for systems with working pressures of 50 psig or 100 psig when appropriate gauge and relief controls are used. All installations are subject to codes established by local utilities or other authorities having
317 240 5662 P. 001/001 PRODUCT DATA ELECTRONIC CONTROL OPTIONS AND FIA COMPONENTS These electronic pilot options are available for Model 246 Gas-Fired Boiler application. FIA does not approve a specific device or unit. Approval applies to the complete installation based upon the locai FIA engineer's evaluation ' of equipment, hazards of building usage, and the insurance liabilities involved, FIA generally recommends that gas-fired sectional boilers be equipped with electronically supervised