Remote switch is on • Adjust remote switch to desired position. Thermostat Fan switch is in On position • Normal operation. HVAC system is running to satisfy heating or cooling requirements. • Normal operation. Ventilation limit is set to 100% ventilation limit. • Set ventilation limit to 60%. The control may not be able to meet the recommended ventilation requirements. • Increase ventilation airflow through fresh air duct and adjust settings. Low ventilation air flow. • See Problem: Not enough
3 Installation ......................................................................... 3 Wiring ................................................................................. 4 XL800 Series Power Consumption ................................ 5 I/O Modules ................................................................... 5 Description of the XCL8010AU Controller Module ......... 7 Overview........................................................................ 7 Interfaces and Bus Connectio
All can be used, but the 75/25 mixture is recommended for general welding. For aluminum welding, use 100% Argon. Either type gas may be obtained at your local welding supply outlet. Secure cylinder in place on your welding machine or other support to prevent the cylinder from falling over. REGULATOR This regulator is designed to be used with straight Argon or Argon mix gas. A threaded adapter is needed if CO2 is used. An adapter is available at your local welding gas supplier to change between t
The remote temperature sensor (TX6U) and mounting bracket (Figure 2) 3. (3) 1/2" Philips screws 4. One strip of double sided adhesive tape 5. Instruction Manual and Warranty Card 6. (2) AAA 1.5V batteries 7. (2) AAA 1.5V batteries ADDITIONAL EQUIPMENT 1. Philips screwdriver (not included) Figure 1 Figure 2 2 QUICK SETUP Hint: Use good quality Alkaline Batteries and avoid rechargeable batteries. 1. Have the indoor temperature station and remote temperature sensor 3 to 5 feet apart. 2. Batteries s
FEATURES • Designed to help meet local ventilation codes and standards, including ASHRAE 62.2-2010 standard, “Ventilation and Acceptable Indoor Air Quality in Low-Rise Residential Buildings.” • Microcontroller optimizes the air delivery schedule to make efficient use of normal HVAC run times. • Easy-to-use input dials allow customized ventilation for each installation. • Test mode that includes immediate feedback to installer to confirm that air delivery requirements of selected ventilation stan
0 W7620 Base Controller provides: -four relay outputs -network communication -T7660 Space Temperature Sensor inputs 0 W7621 Expansion Input Point Boards provide additional input point expansion on one board of up to: -two resistive inputs -two digital inputs - two voltage inputs (one dry contact, one extended 24 Vac input) • W7622 Expansion Output Point Boards provide additional output point expansion on one board of up to: -three analog outputs -three digital outputs 0 T7660 Space Temperature S
See section on DCV setpoint set up on page 4. 63-2569—04 8 W7340, W7345 COMMUNICATING ECONOMIZER LOGIC MODULES W7340, W7345 COMMUNICATING ECONOMIZER LOGIC MODULES On the W7340A and B models, the logic module as shipped from the factory, limits the minimum position setpoint to 50%. The logic module will not allow a minimum position greater than 50% open (from fully closed). NOTE: This setpoint limit can only be changed using a Modbus command. Equation 1. Formula to aid in minimum position adjustm
The W7340 is used with both solid state temperature and humidity or enthalpy sensors. The W7345 is used with solid state temperature sensors only. FEATURES • Solid state control package provides accuracy, reliability and stability. • Housed in high-impact, glass-fiber reinforced plastic case. • Terminals included for connecting optional S963B1136Remote Potentiometer for remote minimum damper position control. • Communicates using a modified Modbus protocol. • Case matches the lines of the M7215
03/03 US1I-6228 Copyright, Notices, and Trademarks © Copyright 2000 by Honeywell Inc. While this information is presented in good faith and believed to be accurate, Honeywell disclaims the implied warranties of merchantability and fitness for a particular purpose and makes no express warranties except as may be stated in its written agreement with and for its customer. In no event is Honeywell liable to anyone for any indirect, special or consequential damages. The information and specifications
Note: The alert is also triggered when you undo the cover to replace batteries in the door camera. MIC volume [For future use] The topmost control along the side (see diagram on page 8) will control the volume produced from a microphone. Adjust for optimum listening level. Scan button When used in a multi-camera system, this button scans through available pictures. Privacy Remember that this product uses the public airwaves, and that the 30-second duration video signal from the door camera(s) ca