1. See Cancelling a Unit Price (WC30) below. /570 j?E .40 2. Cancelling a Unit Price (WC30) If you have retained a Unit Price, then you must cancel it. QUICK STEPS -Cancelling a Unit Price (WC30) 1. Long PRESS [C] 2. Short PRESS [SAVE] To cancel a Unit Price: 1. Long PRESS the [C] key. 2. Short PRESS the [SAVE] key. ^sSortPRESS 3-7 Using World Scale World Scale Using Tare (WC30) You have the following options available on your WC30 Price Computing Scale: ♦ Platter Tare (WC30)
RIDGE AVENUE TROY, OHIO 45374-0001 937-332-3000 com FORM 34733 (June 2002) World Scale World Scale Table of Contents CHAPTER ONE: INTRODUCTION.................................................................................................................1-1 Welcome......................................................................................................................................................1-2 FCC Note.................................................................
This measurement should be taken at several points around the bowl to assure accuracy. To Adjust Bowl / Agitator Clearance • Remove the Apron (which is secured by 4 thumbscrews). • Loosen the Locking Nut on the Stop Screw (Fig. 7), turn the Stop Screw counterclockwise to increase the clearance or clockwise to decrease the clearance. • Tighten the Locking Nut while holding the Stop Screw. • After adjustments are made, replace the Apron. • Reconnect the electrical power supply. • Carefully
G (Aug. 2007) TABLE OF CONTENTS GENERAL ..............................................................................................................................................................3 INSTALLATION ......................................................................................................................................................3 Unpacking .............................................................................................................................
It has a single speed transmission and features a 2V2 horsepower Hobart-built motor, a #12 attachment hub, and an electro-mechanical timer as standard equipment. A 60 quart stainless steel mixer bowl and a 60 quart burnished aluminum ED style dough arm are furnished with each mixer. Bowl Guard is standard equipment on all P660 models. These mixers can be ordered with deluxe finish, which includes a chrome plated transmission case, base, bowl support, and pedestal. Model P660 Mixer Shipping
X 16” LG. 2 2 1183304 Plate, Cover 2 2 1183315 Nipple, Pipe,BLK. 3/8” X 8” 1 1 1183308 Bracket, Arm Adjust 1 1 1183259 Tube, Burner Supply (H) 2 2 1183269 Clip, Retainer 1 1 1183295 Spring, Pivot Arm 1 1 1183332 Bracket, Orifice 4 4 1183311 Spring, Rack 2 2 1183201 Front, Body, 36 1 1 1160484 Roller Bearing 9 9 1183187 Base, 36, SS 1 1 1184990 Handle, Chrome 1 1 1183209 Grease Drawer, BA 1 1 1184192 Knob, Cast Aluminum 2 2 1183210 Body, Bottom/Back, 36 1 1 1060475 Knob, Ball 1 1 1183222 Stiffene
If necessary, adjust the pilots using the following procedure: 1. If necessary, light the pilots. 2. Locate the pilot adjustment screw (which adjusts both pilots). It is a small slotted screw located on the pilot valve, and is accessed though the slot in the front panel above the control-valve knob. 3. Turn the pilot adjustment screw to adjust the size of the pilot flames. The flame on each pilot should be large enough to extend along the flame carrier to the burner surface. ADJUSTMENT OF LOW SE
8. Wipe clean all surfaces. STEP 6: CHECK BROILER OPERATION 1. Turn gas supply on. Immediately check all gas connections for leaks using soapy water. 2. Light the pilots (see the appropriate Operation section elsewhere in this manual). Check that the pilot flames are large enough to extend along the flame carrier to the burner surface. If not, adjust the pilots (see page 20). 3. Infrared: Turn on the broiler burners and check for correct flame appearance and height at both the HIGH and LOW setti
Provide an adequate means of restraint to prevent undue strain on the gas connection. Test pressure should not exceed 14" W.C. PAGE 6 OF 24 INSTALLATION & OPERATIONS MANUAL 1186527 REV 3 (12/06) INFRARED/RADIANT COMPACT BROILER CLEANING & MAINTENANCE If applicable, the vent line from the gas appliance pressure regulator must be installed to the outdoors in accordance with local codes, or in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1, Natural Gas Installation Code, C
Some divisions have negotiated with Hobart to do additional installation work. These services are on a division-by-deviation basis and are invoiced locally to the division. Hobart offices will be notified prior to shipment of bakery oven and proofer. It will include the project manager’s name and phone number. The installing office should contact that person to schedule installation. After Hobart has equipment set in place, they should notify their Kroger contact that the utilities are ready f