info OM5-C Modular Isolated Signal Conditioners Where Do I Find Everything I Need for Process Measurement and Control? OMEGA.. .Of Course! Shop online at omega, com™ TEMPERATURE 0 Thermocouple, RTD & Thermistor Probes, Connectors, Panels & Assemblies 0 Wire: Thermocouple, RTD & Thermistor 0 Calibrators & Ice Point References 0 Recorders, Controllers & Process Monitors 0 Infrared Pyrometers PRESSURE, STRAIN AND FORCE 0 Transducers & Strain Gages 0 Load Cells & Pressure Gages 0 Displacemen

M3618/1100(OM-40-C-HT) 1/25/02 3:36 PM Page 2 W h e re Do I Find Everything I Need for P rocess Measurement and Control? OMEGA…Of Course! Shop online at T E M P E R A T U R E Thermocouple, RTD & Thermistor Probes, Connectors, Panels & Assemblies Wire: Thermocouple, RTD & Thermistor Calibrators & Ice Point References Recorders, Controllers & Process Monitors Infrared Pyrometers PRESSURE, STRAIN AND FORCE Transducers & Strain Gages Load Cells & Pressure Gages Displacement Transducers Instrumentati

Refer to Figure 1. The loop supply voltage vs. loop resistance shows the minimum supply voltage (Vmin) required for a given loop resistance (RLOOP). Excitation (Ratiometric Output Only) For proper operation a voltage within the range of 5 to 10 Vdc must be applied between the transducer’s supply terminals. Noise For minimum noise susceptibility, avoid running the transducer’s cable in a conduit that contains high current AC power cables. Where possible avoid running the cable near inductive equi

To continue pumping, turn on the unit’s power. The display returns to the STOPPED Display Mode and shows the current RPM setting. The accumulated time of pumping and volume dispensed is reset to zero. Then press the START/STOP key. START STOP xxx rpm Pump(s) stops; press again pump(s) starts To resume pumping at the current setting, press the START/STOP key. The display enters the RUNNING Display Mode, and the fluid begins to dispense. INLET SELECT Must STOP first! LEDs indicate new pump directi

Combined with one of our pressure calibrators, the PPA100 makes a complete Pressure/ Vacuum Calibration System. Operation The drawing shows the operation of the controls on the PPA100. The pump is designed for use with ambient air only. Pump Valve Assembly Cleaning Instructions Occasionally, the PPA100 may not work properly due to dirt or other contamination of the internal valve assembly. Use the following procedure for cleaning the valve assembly. 1. Using a small screwdriver, remove the 2 val

net Display Size:.43’ high Front Panel Rating: NEMA-4X when mounted with gasket provided Case Material: Cycolac X-17 TOTALIZER Type: Up/Down Counting Digits: 8 digits positive/minus sign and 7 digits negative Scaler: 0.0001-100.0000 (0.0000 scales by 100 ) Decimal Point: 5 positions, programmable DC COMMON (Terminal 1) EXTERNAL RESET INPUT (Terminal 4) Resets totalizer when connected to dc common. Minimum Low Time: 0.25 to 1 .O sec. (maintained) The required pulse width varies with count speed,

Please check the functions of the instrument you have purchased before you proceed. RANGE Models Operating Range Overrange HHP-2000, 2020, 2080 25mbar / 10” HO2 350mbar / 140 H O2 ” HHP-2001, 2021, 2081 130mbar / 52 H O2 ” 1bar / 401 H O2 ” HHP-2002, 2022, 2082 2bar / 28 PSI 4bar / 58 PSI HHP-2003, 2023, 2083 7bar / 101.5 PSI 10bar / 145 PSI HHP-2024, 2084 External Transducer - HHP-2005, 2025, 2085 2bar absolute 4bar HHP-2026, 2086 10bar / 145 PSI 10.342bar / 150 PSI FEATURES Models Features HHP

OMEGA is constantly pursuing certification of its products to the European New Approach Directives. OMEGA will add the CE mark to every appropriate device upon certification. The information contained in this document is believed to be correct, but OMEGA Engineering, Inc. accepts no liability for any errors it contains, and reserves the right to alter specifications without notice. WARNING: These products are not designed for use in, and should not be used for, patient-connected applications. PX

ol: (001) 203-359-7803 e-mail: espanol@omega.com FAX: ( 001) 203-359-7807 info@omega.com.mx Servicing Europe: Benelux: Postbus 8034, 1180 LA Amstelveen, The Netherlands Tel: +31 (0)20 3472121 FAX: +31 (0)20 6434643 Toll Free in Benelux: 0800 0993344 e-mail: sales@omegaeng.nl Czech Republic: Frystatska 184, 733 01 Karvina, Czech Republic Tel: +420 (0)59 6311899 FAX: +420 (0)59 6311114 Toll Free: 0800-1-66342 e-mail: info@omegashop.cz France: 11, rue Jacques Cartier, 78280 Guyancourt, France Tel:

RETURN REQUESTS / INQUIRIES Direct all warranty and repair requests/inquiries to the OMEGA Customer Service Department. BEFORE RETURNING ANY PRODUCT(S) TO OMEGA, PURCHASER MUST OBTAIN AN AUTHORIZED RETURN (AR) NUMBER FROM OMEGA S CUSTOMER SERVICE DEPARTMENT (IN ORDER TO AVOID PROCESSING DELAYS). The assigned AR number should then be marked on the outside of the return package and on any correspondence. The purchaser is responsible for shipping charges, freight, insurance proper packaging to prev