Login:
Sorted: Name ↑   Downloads   Rate   Size ↑  

Nordyne G6RC 90+

downloaded: 43File size: 650 kb    Manafacture: Nordyne  
Category: Electric Heaters

Airflow rates of 1800 CFM or more ** Factory Set Heating Speed 2. Temperature rises in the table are - Not Recommended 3. Temperature rises and airflows These conditions are not recommended. INSTALLATION REQUIREMENTS • NFPA-90B - Warm Air Heating and Air Conditioning Systems. Requirements and Codes This furnace must be installed in accordance with these instructions, all applicable local building codes, and the current revision of the National Fuel Gas Code (ANSI-Z223.1, NFPA-54). The current re

Nordyne M1B

downloaded: 30File size: 1 mb    Manafacture: Nordyne  
Category: Electric Heaters

Recreational Vehicles, Park Models, Manufactured Buildings 3. Modular Homes/Buildings ! WARNING: If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury or loss of life. – Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. – WHAT TO DO IF YOU SMELL GAS • Do not try to light any appliance. • Do not touch any electrical switch; do not use any phone in your buil

Nordyne M1S

downloaded: 10File size: 1 mb    Manafacture: Nordyne  
Category: Electric Heaters

Flashing 1/2 second on, 1/2 second off - system is locked out or in restricted mode. 2. Flashing 2 seconds on, 2 seconds off - control is in recycle mode. 3. Indicator light is on - cad cell is sensing flame. 4. Indicator light is off - cad cell is not sensing flame. may be defective. Replace the gas valve if necessary. e. Be sure the pilot shield is in place. f. Check for gas leaks in the pilot line or the pilot assembly. g. Check the flue assembly to make sure all connections are tight. h. See

Nordyne M1G

downloaded: 4File size: 1 mb    Manafacture: Nordyne  
Category: Electric Heaters

d. Cut out duct opening 1/4" larger than area marked. INSTALL FURNACE MOUNTING PLATE a. Place mounting plate (supplied within duct connector) at rear of the floor opening (See Figure 15). INSTALLING PLATINUM SERIES 14” ROUND DUCT CONNECTOR a. Place duct connector through the floor opening. (See Figure 15). b. Secure duct connector to floor. INSTALLING SCREW DOWN DUCT CONNECTOR a. Apply a bead of caulking, mastic, or other approved sealant around bottom side of 1/2” flange and restrictor plate, w

Nordyne G6RL 90+

downloaded: 3File size: 650 kb    Manafacture: Nordyne  
Category: Electric Heaters

This screen is provided with the furnace installation instructions and functions to prevent debris from entering the combustion system. It should be installed on the combustion air intake collar or inlet PVC. If furnace location is such that this opening might be unintentionally obstructed, a 3" PVC elbow should be installed on the collar, and the screen placed inside the inlet of the elbow. See Figure 8. Installation In An Unconfined Space ! CAUTION: "Tight" buildings (with weather stripping an

Nordyne CMF

downloaded: 2File size: 144 kb    Manafacture: Nordyne  
Category: Electric Heaters

If a problem occurs, check the instructions and follow recommendations given. If these suggestions don’t eliminate your problem, call your NORDYNE Servicing Contractor (Service PRO). A list of available Service PRO's is included for your convenience. TURNING ON YOUR HEATING SYSTEM Your Wall Thermostat Responding to changes in room air temperature, the thermostat automatically turns your furnace on and off to maintain the comfort level you select. Your thermostat is a sensitive instrument. DO NOT

Nordyne RL 90+

downloaded: 1File size: 996 kb    Manafacture: Nordyne  
Category: Electric Heaters

These couplings can be ordered through your local furnace distributor. To install a coupling, slide the rubber coupling over the end of the pipe that is attached to the furnace and secure it with one of the hose clamps. Then slide the other end of the rubber coupling onto the other pipe from the vent and secure the coupling with the second hose clamp. Ensure that the connection is tight and leak free. NORDYNE condensing furnaces have been certified for installation with zero clearance between ve

Nordyne Residential Gas Furnaces

downloaded: 1File size: 547 kb    Manafacture: Nordyne  
Category: Electric Heaters

— WHAT TO DO IF YOU SMELL GAS: • Do not try to light any appliance. • Do not touch any electrical switch; do not use any phone in your building. • Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's instructions. • If you cannot reach your gas supplier, call the fire department. • Extinguish any open flame. — Installation and service must be performed by a qualified installer, service agency, or the gas supplier. ! AVERTISSEMENT: RISQUE D’INCENDIE OU D’EXPLOSION

Nordyne R-410A

downloaded: 1File size: 347 kb    Manafacture: Nordyne  
Category: Electric Heaters

Standards. Split System Heat Pump units are designed for use with a wide variety of fossil fuel furnaces, electric furnaces, air handlers, and evaporator coil combinations. These instructions are primarily intended to assist qualified individuals experienced in the proper installation of heating and/or air conditioning appliances. Some local codes require licensed installation/ service personnel for this type of equipment. Read all instructions carefully before starting the installation. USER’S

Nordyne M3RL Series

downloaded: 0File size: 1 mb    Manafacture: Nordyne  
Category: Electric Heaters

! ADVERTISSEMENT: RISQUE D’INCENDIE OU D’EXPLOSION Le non-respect des avertissements de securite pourrait entrainer des blessures graves, la mort ou des dommages materiels. – Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. – WHAT TO DO IF YOU SMELL GAS • Do not try to light any appliance. • Do not touch any electrical switch; do not use any phone in your building. • Leave the building immediately. • Immediately call your gas supp





Category