6.2.1 Pumping in the FLOW RATE Mode To pump fluid in the FLOW RATE Mode, do the following: 1. Set up the pump motor for pumping, according to Chapter 3. 2. Toggle the ON/OFF switch to turn on the unit’s power. The display is in the STOPPED Display Mode. Refer to Figure 6-3. 3. Either set the TUBE ID for the tube you are using (following Section 5.3) or calibrate the tube (following Section 5.5), before continuing. 4. Press the FLOW RATE key. FLOW RATE Display shows xxx mL/min ACTION Displays cur

OMEGA Warranty adds an additional one (1) month grace period to the normal one (1) year product warranty to cover handling and shipping time. This ensures that OMEGA’s customers receive maximum coverage on each product. If the unit should malfunction, it must be returned to the factory for evaluation. OMEGA’s Customer Service Department will issue an Authorized Return (AR) number immediately upon phone or written request. Upon examination by OMEGA, if the unit is found to be defective it will be

Box 4047 ISO 9001 Certified Stamford CT 06907-0047 TEL: (203) 359-1660 FAX: (203) 359-7700 e-mail: info@omega.com Canada: 976 Bergar Laval (Quebec) H7L 5A1 TEL: (514) 856-6928 FAX: (514) 856-6886 e-mail: info@omega.ca For immediate technical or application assistance: USA and Canada: Sales Service: 1-800-826-6342 / 1-800-TC-OMEGA® Customer Service: 1-800-622-2378 / 1-800-622-BEST® Engineering Service: 1-800-872-9436 / 1-800-USA-WHEN® TELEX: 996404 EASYLINK: 62968934 CABLE: OMEGA Mexico: TEL: (00

Install Jumper onto S1-A on Component Side of Board. Version A Version B Testpoint/Jumper Locations Page 5 IV. COMMANDS FOR ACCESSING EEPROM: NO. command letter index meaning # of bytes 1. R,W 01 Input range or function 1 2. R,W 02 Input/output Configuration 1 3. R,W 03 Decimal point 1 4. R,W 04 Filter time constant 1 5. R,W 05 Reading scale 3 6. R,W 06 Reading offset 3 7. R,W 07 Communication parameters 1 8. R,W 08 Communication bus format 1 9. R,W 09 Communication Data format 1 10. R,W 0A Comm

Box 4047 ISO 9001 Certified Stamford, CT 06907-0047 TEL: (203) 359-1660 FAX: (203) 359-7700 e-mail: info@omega.com Canada: 976 Bergar Laval (Quebec) H7L 5A1 TEL: (514) 856-6928 FAX: (514) 856-6886 e-mail: info@omega.ca For immediate technical or application assistance: USA and Canada: Sales Service: 1-800-826-6342 / 1-800-TC-OMEGA® Customer Service: 1-800-622-2378 / 1-800-622-BEST® Engineering Service: 1-800-872-9436 / 1-800-USA-WHEN® TELEX: 996404 EASYLINK: 62968934 CABLE: OMEGA Mexico: (001) 8

To use the RS485 communication for the Signal Conditioners you’ll need an available Communication port in your computer and have access to a generic communication software program (e.g.: Procomm1, Windows2 HyperTerminal3, etc, see details below for information). A RS485 signal conditioner communication software program is also available as an option to speed the set-up. A RS232 to RS485 converter box will also be required if your computer communications port is RS232. 1 Procomm is a registered t

This output will drive any OMEGA® flow ratemeter, counter, controller or pulse input data acquisition board. Unpacking Remove the Packing List and verify that you have received all equipment. If you have any questions about the shipment, please call the Customer Service Department. When you receive the shipment, inspect the container and equipment for any signs of damage. Note any evidence of rough handling in transit. Immediately report any damage to the shipping agent. NOTE The carrier will no

You can send another command after you receive the . i.e. send: *01X01 response: 01X01 Note: Only for reading (X01 command). 01 is address. Frequency mode: response time is controlled by the gate time. If gate time is increased then response time is longer. Other modes: response time is not controlled by the gate time. WARM UP TO RATED ACCURACY: 30 minutes INPUT POWER: 10 to 32 Volt DC POWER CONSUMPTION: 3 Watts (125mA at 24V DC) OPERATING AMBIENT: -5 to +55 °C STORAGE TEMPERATURE:

These units feature an SPDT switch, which can be triggered at any point along the flow range FEATURES • Strong, completely sealed die cast aluminum body, water and oil tight • Forrped double sealed aluminum cover (with lip) anodized • Unbreakable Lexan window (full cover) • Oversize neoprene cover gasket matches with double ribbed lip of die cast body. Other seals — Buna-N • Chrome plated pan head cover screws with screw retainers • Wire guards • Easy wire top screw micro switch • Mount

Normal system filtrsitions should be sufficient. Systems which do not have any filtration should be equipped with at least a 200 m6sh sjeve or 74 micron filter. Most hydraulic systems would already have a much finer filtration. Within the cartridge dirt or sealing agents, such as Teflon tape, may lodge within and cause malfunction. If a malfunction does occur and you are using proper filtration, we would recommend disassembly and cleaning. This Can be done as follows: On clean bench, remove sm