Aural Sweep Test M.F. Aural Sweep Test H.F. Aural Sweep Test 6.0V Input 30Hz to 20kHz 6.0V Input 30Hz to 2kHz 4.0V Input 500Hz to 6kHz 2.83V Input 4kHz to 20kHz PHYSICAL SPECIFICATIONS: • Enclosure Dimensions 42" x 14-1/2" x 12" (H x W x D) 1067mm x 368mm x 305mm • Weight 55 lb/25kg (each) WARRANTY: • Refer to Warranty Statement packed with each product. • The maximum recommended amplifier power rating will ensure proper system headroom to allow for occasional peaks. We do not recommend

Introduction...................................................................................... 3 1.1 Features .................................................................................... 4 1.2 About Installation ...................................................................... 4 2. Installation and use.......................................................................... 5 3. System Design with the GTH400..................................................... 6 3.1 Speaker Req

• At the installation sites, locate and make a note of all fuel lines, hydraulic brake lines, vacuum lines and electrical wiring. Use extreme caution when cutting or drilling in and around these areas. • Choose a safe mounting location away from moisture. • Make sure there is sufficient air circulation at the mounting location for the amplifier to cool itself. • Mount the amplifier, using the supplied hardware. Specifications • 40W RMS x 2 @ 4 ohms and .1% THD + N* • 60W RMS x 2 @ 2 ohms, 14.4V

• At the installation sites, locate and make a note of all fuel lines, hydraulic brake lines, vacuum lines and electrical wiring. Use extreme caution when cutting or drilling in and around these areas. • Choose a safe mounting location away from moisture. • Make sure there is sufficient air circulation at the mounting location for the amplifier to cool itself. • Mount the amplifier, using the supplied hardware. Specifications • 55W RMS x 4 channels, plus 225W RMS x 1 channel, @ 4 ohms and .1% TH

In order that we may better serve you should you require warranty service for your new amplifier, please retain your original purchase receipt and return the enclosed warranty registration card. INSTALLATION WARNING: Playing loud music in an automobile can hinder your ability to hear traffic and permanently damage your hearing. We recommend listening at low or moderate levels while driving your car. JBL accepts no liability for hearing loss, bodily injury or property damage resulting from the us

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and then on, the user is encouraged to try to correct the interference by one or mo

Failure to adequately protect the positive wire from potential damage may result in a vehicle fire. When you are done routing and connecting this wire, you may install the fuse at the battery. Remote Connection Connect the amplifier’s Remote (REM) terminal to the source unit’s Remote Turn- On lead using a minimum of 18-gauge wire. NOTE: When using the speaker level inputs, connect the remote (REM) terminal to the source unit. If your source unit does not have a remote turn-on connection, connect

INSTALLATION 2 THANK YOU for purchasing a JBL CS Series amplifier. In order that we may better serve you should you require warranty service for your new amplifier, please retain your original purchase receipt and register your new JBL amplifier online at WARNING Playing loud music in an automobile can hinder your ability to hear traffic and permanently damage your hearing. We recommend listening at low or moderate levels while driving your car. JBL accepts no liability for hearing loss, bodily

(SP) Configuración de los altavoces en la función de las entradas e instalada. RCAINPUT CH1/CH2 CH3/CH3 SWITCH INPUT 4CH 2CH SWITCH OUTPUT DUAL SPEAKER OUTPUT CONFIGURATION * * * * * * * 4or2 ohm 4or2ohm 4or2ohm * * * * * * * Speakersoutput m? CH1/CH2 Speakersoutput m? CH3/CH4 4or2 ohm 4ohmONLY * * * - : Speakersoutput 1 m? a CH1/CH2 0 : 1 J Speakersoutput -, + i m? o n CH3/CH4 o 1 J 4ohmONLY 4ohmONLY 06 J CH1/CH2 Speakers connection (

For example, in Figure 4, each woofer you should design a speaker system will have an impedance of 12 ohms, by based on the RMS power handling of The JBL A6000GTi and A3000GTi your speakers. For music with sharp Ztotal = Z1 + Z2 = 6 + 6 = 12 amplifiers support a wide range of transient bass notes (e.g., rock, and the three woofers connected country or jazz), the RMS power impedances, and any speaker system in parallel will have an equivalent handling rating is conservative, and with a total or e