Login:
Sorted: Name ↑   Downloads   Rate   Size ↑  

Kidde SS041

downloaded: 32File size: 604 kb    Manafacture: Kidde  
Category: Alarms

Clear log to reset 20% or less remaining. When full the instrument will start overwriting the old data. Contact HSS Hire if the downloaded log is required. 32 Gas log nearly full. Clear log to reset 20% or less remaining. When full the instrument will start overwriting the old data. Warning Codes Number Message Action or Reason 12 Check batteries Mixed battery types, i.e. one dry cell, one rechargeable. Fit two of the same type. 13 Battery empty. Check batteries Battery too low to operate instru

Kidde KN-COPE-I

downloaded: 11File size: 208 kb    Manafacture: Kidde  
Category: Alarms

The test/reset button has four purposes. It tests the unit’s electronics, resets the CO alarm, activates the HUSH feature, and activates the Peak Level Memory Feature. After installation, TEST THE UNIT’S ELECTRONICS by pressing and releasing the test/reset button. A series of beeps will sound, followed by the message “Fire! Fire!” then another two series of beeps and the message “WARNING! CARBON MONOXIDE!” followed by 4 additional short beeps. Weekly testing is required! If at anytime it does no

Kidde KN-COB-B-LS (900-0233)

downloaded: 8File size: 242 kb    Manafacture: Kidde  
Category: Alarms

See “What to do When the Alarm Sounds” (inside front cover). Possible Sources of Carbon Monoxide Inside your home, appliances used for heating and cooking are the most likely sources of CO. Vehicles running in attached garages can also produce dangerous levels of CO. CO can be produced when burning any fossil fuel, such as gasoline, propane, natural gas, oil and wood. It can be produced by any fuelburning appliance that is malfunctioning, improperly installed, or not ventilated correctly, such a

Kidde I12040

downloaded: 8File size: 308 kb    Manafacture: Kidde  
Category: Alarms

This alarm uses ionization sensing technology. Ionization sensing alarms may detect invisible fire particles (associated with flaming fires) sooner than photoelectric alarms. Photoelectric sensing alarms may detect visible particles (associated with smoldering fires) sooner than ionization alarms. Kidde strongly recommends that both ionization and photoelectric smoke alarms be installed to help insure maximum detection of the various types of fire that can occur within the home. This smoke alarm

Kidde KN-COP-DP-LS

downloaded: 8File size: 173 kb    Manafacture: Kidde  
Category: Alarms

When choosing your installation locations, make sure you can hear the alarm from all sleeping areas. If you install only one CO alarm in your Recommended Locations home, install it near bedrooms, not in the basement or furnace room. • When wall mounting, place out of reach of children. Under no circumstances should children be allowed to handle the CO alarm. Locations To Avoid IMPORTANT: Improper location can affect the sensitive electronic components in this alarm. To avoid causing damage to th

Kidde 1235

downloaded: 7File size: 136 kb    Manafacture: Kidde  
Category: Alarms

•When alarms are interconnected, all interconnected units must be powered from a single circuit. •A maximum of 24 Lifesaver devices may be interconnected in a multiple station arrangement. The interconnect system should not exceed the NFPA interconnect limit of 12 smoke alarms and/or 18 alarms total (smoke, heat, etc.) With 18 alarms interconnected, it is still possible to interconnect up to a total of 6 remote signaling devices and/or relay modules. •When mixing models which have battery backup

Kidde I9070

downloaded: 6File size: 318 kb    Manafacture: Kidde  
Category: Alarms

If you are not sure about the insulation in your mobile home, or if you notice that the outer walls and ceiling are either hot or cold, install the alarm on an inside wall. For minimum protection, install at least one alarm close to the sleeping rooms. For additional protection, see SINGLE FLOOR PLAN in figure 2. WARNING: TEST YOUR SMOKE ALARM OPERATION AFTER RV OR MOBILE HOME VEHICLE HAS BEEN IN STORAGE, BEFORE EACH TRIP AND AT LEAST ONCE A WEEK DURING USE. 2. Locations To Avoid • In the garage

Kidde 1275E

downloaded: 6File size: 97 kb    Manafacture: Kidde  
Category: Alarms

This smoke alarm has the ability to function as a single unit or in an interconnected system. The Kidde 1275E features a red LED to display normal operation and identifies the origination unit in an interconnected system. The Kidde 1275E includes an Alarm Tamper Resist that inhibits unauthorized alarm and battery removal. The 1275E is interconnectable and includes a quick connect power harness that allows for quick and easy installation. Consumer Benefits The Kidde 1275E 120VAC powered ionizatio

Kidde 9CO5-LP

downloaded: 6File size: 357 kb    Manafacture: Kidde  
Category: Alarms

Alerts user to replaceCO alarm after 7 yearsNEWFEATURE: Alerts user to replace CO alarmafter 7 years of operationNEWFEATURE: Description The Kidde 9CO5 battery operated carbon monoxide alarm utilizes sophisticated electronic components to protect you and your family from the dangers of carbon monoxide. This alarm includes a slide-out battery door that gives immediate access to the batteries and a safety feature that makes it difficult to close the door without the batteries being installed. Insi

Kidde 1296

downloaded: 5File size: 111 kb    Manafacture: Kidde  
Category: Alarms

The Kidde 1296E is designed to alert you and your family from the dangers of smoke and fire. This smoke alarm utilizes an ionization sensor. (For maximum protection Kidde recommends that both photo- electric and ionization smoke alarm be used). The 1296E has interconnect capabilities and can be interconnected up to 24 Kidde devices including smoke alarms, CO alarms and heat alarms. The 1296E includes a 9V battery backup to provide continuous protection, even during a power failure along with a 5





Category