Login:
Sorted: Name ↑   Downloads   Rate   Size ↑  

Wayne ESP15

downloaded: 42File size: 861 kb    Manafacture: Wayne  
Category: Swimming Pools

5. A single thirty-second tone will sound when power to the system is interrupted. The unit will reset automatically when power is restored. A three-second tone will sound every time the pump starts. Troubleshooting Chart Maintenance Always disconnect the electrical supply before attempting to install, service, relocate or perform any maintenance. If the power source is out of sight, lock and tag in the open (off) position to prevent unexpected power application. Failure to do so could result in

Wayne WLS150

downloaded: 25File size: 265 kb    Manafacture: Wayne  
Category: Garden Tools

4. After the proper depth is reached, install a well seal or pitless adapter to support the pipe. 5. Slope the horizontal pipe upward toward the pump to eliminate trapping air. 6. When using a foot valve, a priming tee and plug above the well seal is recommended. DRIVEN WELL • Drive the point several feet below the water table. NOTE: A packer-type foot valve can be installed in the well (See Figure 3). This type of foot valve allows the well pipe to be filled with water when priming and makes th

Wayne WIP100

downloaded: 17File size: 261 kb    Manafacture: Wayne  
Category: Swimming Pools

Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or property damage! Retain instructions for future reference. Pool Pumps Description This swimming pool pump is designed for use with permanently installed pools only. These pools can be either in-ground or above-ground. Unpacking After unpacking the unit, carefully inspect for any damage that may have occurred during transit. Check for loose, missing or damage

Wayne DSP75

downloaded: 12File size: 275 kb    Manafacture: Wayne  
Category: Plumbing Product

Read carefully before attempting to assemble, install, operate or maintain the product described. Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or property damage! Retain instructions for future reference. Operating Instructions and Parts Manual Models DSP60 and DSP75 Description A sewage pump is intended for use in domestic sewage lift stations. It is suitable for pumping sewage, effluent, wastewater, gro

Wayne WIP150

downloaded: 11File size: 261 kb    Manafacture: Wayne  
Category: Swimming Pools

After about 10 minutes of operation, check the return fittings for air bubbles. A continuous flow of air indicates leaks in the suction line. Locate and correct any leaks immediately. CONTROLLING PUMP DISCHARGE Keep the gate valve in the suction line fully open during operation. To control the discharge, use a valve in the return line. Do not retighten strainer Ring-lok during operation. Do not operate pump with closed suction or discharge valve. WATER CHEMISTRY Proper and consistent use of chem

Wayne WLS200

downloaded: 10File size: 265 kb    Manafacture: Wayne  
Category: Garden Tools

The water inside the pump could boil and damage the pump. Maintenance Maintain adequate ventilation for the pump motor. The motor bearings are permanently lubricated at the factory. Additional lubrication is not required. DRAINING FOR WINTER Always protect pump and piping against freezing temperatures. If there is any danger of freezing, drain the system. To drain the system: 1. Remove the pipe plug from the discharge tee. 2. Remove the 1/4” plug from the lower front face of the pump. 3. Drain a

Wayne 330600-001

downloaded: 10File size: 275 kb    Manafacture: Wayne  
Category: Plumbing Product

4. Place the pump in a suitable area where it can be cleaned thoroughly. Remove all scale and deposits on pump. 5. Submerge the complete pump in a disinfectant solution (10% chlorine bleach solution) for at least one hour before handling the pump. 6. Clean all dirt and deposits from the pump float. Make sure float moves freely after cleaning. 7. Clean all dirt and deposits away from pump inlet and volute. This pump contains dielectric motor oil for lubrication and motor heat transfer. This oil c

Wayne P250AF

downloaded: 8File size: 244 kb    Manafacture: Wayne  
Category: Convection Ovens

English values take priority. FOR YOUR SAFETY IF YOU SMELL GAS: 1. OPEN WINDOWS 2. DON’T TOUCH ELECTRICAL SWITCHES 3. EXTINGUISH ANY OPEN FLAME 4. IMMEDIATELY CALL YOUR GAS SUPPLIER. WARNING: If the information in these instructions is not followed exactly, a fire or explosion may result causing property damage, personal injury or death. -Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. -WHAT TO DO IF YOU SMELL GAS • Do not try to

Wayne SEP6

downloaded: 6File size: 835 kb    Manafacture: Wayne  
Category: Plumbing Product

Cutting the cord or plug will void the warranty and make the pump inoperable. Figure 4 - Typical Installation Three prong grounded outlet equipped with a ground fault interruptor Main waste line to sewer or septic tank 2 in. Discharge pipe Upper level drainage Cleanout Pump Float Switch Flange Floor drain Dryer Washer Laundry tubs Vent pipe Lavatory Shower Washer drain 45° Elbow 2 in. Check valve 2 in. gate valve Operating Instructions and Parts Manual Union Operating Instructions and Parts Manu

Wayne SEL40

downloaded: 6File size: 655 kb    Manafacture: Wayne  
Category: Plumbing Product

angle with the valve pivot on top. In a vertical position, solids will tend to lodge on the valve flapper and can prevent it from opening. 3. Drill a 1/8 inch hole in the discharge pipe approximately 1 inch to 2 inch above the pump discharge when a check valve is used. The hole prevents air locking of the pump at the initial start-up and if it should lose prime. 4. A gate valve should be installed in the system after the check valve. This gate valve should be a full port valve which will pass 2





Category