If the appliance is immersed in water, do not attempt to reset the ALCI safety device. Please take the unit to the nearest service facility for examination. The ALCI safety device is equipped with a test button so that its operation can be checked. TO USE: 1. Press the reset button on the ALCI safety device. 2. Plug appliance into AC electrical outlet. 3. Then press the test button. The reset button will pop out. This verifies the safety device is operating properly. Should the reset button not

or sink. n No coloque ni guarde el aparato donde se pueda caer o ser arrojado n Do not place in or drop into water or other liquid. en la tina o lavamanos. n If an appliance falls into water, "unplug it" immediately. Do not reach n No lo coloque ni lo tire dentro del agua u otra clase de liquidos. into the water. n Si un aparato electrico cae dentro del agua, “desenchufelo” WARNING - To reduce the risk of burns, electrocution, fire, or injury inmediatamente. No introduzca la mano en el agua. to

At any time, should this unit detect an electrical shock hazard, it will immediately shut off. To restore power, the reset button on the ALCI safety device must be pressed to reactivate the circuit. CAUTION: Heating section should never be touched as it may be hot and burns may occur. To avoid possible scalp or hair burns, use very hot setting only when hair is wet. Reduce to lower heat as hair dries. Do not keep appliance directed at one place; keep it in constant motion. This is especially imp

The ESP/ALCI safety device is equipped with a test button so that its operation can be checked. TO USE (See Fig. A): 1. Press the reset button on the ESP /ALCI safety device. 2. Plug appliance into AC electrical outlet. 3. Then press the test button. The reset button will pop out. This verifies that the safety device is operating properly. Should the reset button not pop out, do not use the unit. Return immediately for service. 4. Press the reset button to re-activate the ESP /ALCI safety device

Return immediately for service. 4. Press the reset button to reactivate the ESP/ALCI safety device and use the appliance. At any time, should this unit detect an electrical shock hazard, it will immediately shut off. To restore power, the reset button on the ESP/ALCI safety device must be pressed to reactivate the circuit. Repeat the above procedure each time this appliance is used to confirm that the safety device is operational. IMPORTANT: Never block air intake grille, as this will cause the

Grille Screw Tornillo para la parrilla Vis de la grille 2. Front Grille Parrilla frontal Grille avant 3. Blade Cap Tapa Capuchon des pales 4. Fan Blade Paleta Pales 5. Plastic Collar Anillo de plastico Collier en plastique 6. Rear Grille Parrilla trasera Grille arriere 7. Motor Shaft Eje del motor Arbre du moteur 8. Shaft Pin Clavija del eje Pignon du moteur 9. Oscillating Knob Perilla para oscilacion Bouton d’oscillation 10. Speed Control Switch Interruptor para el Control de Velocidad Commande

It is for household use and may be plugged into any AC electrical outlet (ordinary household current). Do not use any other electrical outlet. HOW ESP/ALCI WORKS The ESP/ALCI safety device in this unit is built into the plug. This device will make it inoperable under some abnormal conditions, such as accidental immersion in water. If the appliance is immersed in water, do not attempt to reset the ESP/ALCI safety device. Please take the unit to the nearest service facility for examination. The ES

CARE AND CLEANING This appliance requires little maintenance and contains service personnel if servicing is needed. This fan is permanently lubricated and will not TO CLEAN: Before cleaning, turn fan off and unplug from ensure adequate air circulation to the motor, keep vents located at the rear of the motor cleaner hose can be used to clean these blade (Fig. 1). Grilles and blade may Use a soft, slightly damp cloth to wipe fan parts. Do not allow water or any have dried completely. Do not plug

Applying pressure, insert bottom pipe into the center opening of the base. On base underside, insert locking pin into bottom pipe hole (Fig.2). Using a Phillips screwdriver, slide locking pin over screw post and secure with screw provided. 2. Align top pipe to the connector indentation points on the bottom pipe. Place top pipe onto the connector. Turn top pipe to the left (from position 0 to position 1) to secure (Fig. 3). 3. Slide the fan housing neck connector down over the top pipe. Make sure

IMPORTANT SAFETY INSTRUCTIONS When using electrical appliances, basic safety . Do not put foreign objects inside the air cleaner. precautions should always be followed, including . Do not operate any appliance with a damagedthe following: cord or plug, if fan motor fails to rotate, or after . Read all instructions before using the appliance. the appliance malfunctions or has been dropped . To avoid fire or shock hazard, plug the air cleaner or damaged in any manner. Return appliance to directly