/Del. Valve Seat 6 73 1802 0279 Spring 1 6 3604 0017 Suct. /Del. Valve 6 74 1227 0051 Ring Nut 1 7 1802 0177 Spring 6 75 3622 0049 Stop Adjustable Nut 1 8 1205 0025 Suct. /Del. Valve Cage 6 76 0009 0367 Spring Spacer 1 9 1210 0048 O-Ring 6 77 2409 0148 Rod 1 10 3202 0315 Plug + O-Ring 6 78 0009 0365 Ring 1 11 3609 0088 Screw 3 79 1210 0613 O-Ring 1 12 1004 0012 Crankcase Flange 1 80 1210 0614 O-Ring 1 13 0402 0329 Aluminum Cover 1 81 0009 0366 Ring 1 14 1210 0386 O-Ring 1 82 0204 0071 Bushing 1

Depress trigger on gun and drain all water out of gun/lance. RV Antifreeze Funnel Hose Water Inlet Problem Solution Motor will not start SOLUTION: A,B Low/Surging pressure or no water flow SOLUTION: C,D,E,F,G,H No chemical injection SOLUTION: I,J,K,L Cause Solution A- Tripped GFCI cord Reset GFCI cord B- Tripped motor relay Reset motor C- Insufficient water supply See water supply section of this manual D- Plugged pump inlet filter See maintenance section of this manual E- Wrong nozzle Make sure

Follow the chemical manufacturer’s recommendations. Understand all safety precautions and first aid for all chemicals. 1. Insert chemical suction line and strainer into a container of detergent. 2. Completely open the chemical control knob located on the chemical injector. 3. Insert the chemical application nozzle (Black). 4. Turn the chemical control knob to adjust the chemical concentration. Spray detergent onto the surface and allow it to soak. Chemicals need time (dwell time) to work properl

Vour machine is designed for long life, dependability, and the top performance you demand. Please take time now to read through this manual so you can better understand the machine's operation, maintenance and safety precautions. Everyone who operates this water pump must read and understand this manual. The time you take now will prolong your water pump's life and prepare you for its safe operation. Enjoy the exceptional performance of your Mustang Semi Trash Series water pump. THIS PUMP CAN P

2.) Risk of fire and explosion. Do not add fuel when engine is running or still hot. 3.) Breathing hazard. Poisonous fumes from engine can kill you. Do not operate indoors even if ventilated. 4.) Risk of electrocution. Keep water away from electric outlets and electric devices. 5.) Read owner's manual. Serious injury or death can result if safety instructions are not followed. ©2003 K-Bar Industries 800-270-0810 Part No. 38570 START-UP INSTRUCTIONS 1. Attach garden hose. 2. Attach pressure hose.

RING 3 32 90.3572.00 O-RING 3 33 52.0400.09 PISTON 3 34 96.7008.00 WASHER 3 VALVE KIT SEAL KIT 123 130 ITEM PART # QTY ITEM PART # QTY 4 90.3841.00 6 40 90.3612.00 1 5 36.2003.66 6 41 44.0800.70 1 6 36.2001.76 6 42 52.2166.70 1 7 94.7376.00 6 43 90.2622.00 1 8 36.2025.51 6 44 90.2620.00 1 45 51.1000.51 1 51 90.2617.00 1 ITEM PART # DESCRIPTION QTY 35 92.2216.00 NUT 3 40 90.3612.00 O-RING 3 41 44.0800.70 PACKING RETAINER 3 42 52.2166.70 INTERMEDIATE RING 3 43 90.2622.00 PACKING 3 44 90.2620.00 PA

Any Questions, Comments, Problems or Parts Orders Call NorthStar Product Support 1-800-270-0810 Engine is shipped without oil. - Before starting engine, fill engine oil. - See engine manual for engine oil requirements. Pump is shipped with oil. - Remove shipping plug and install vented fill cap. (Comet Pumps) - Remove shipping tape from pump oil fill cap. (Cat Pumps) - See pump oil cap section of this manual. Closely inspect all components. -If you have damaged components then: Contact the freig

The supply hose should have a 3/4” inside diameter (ID) and be no longer than 50 feet. 2. The water supply pressure must be a minimum of 20 pounds per square inch (PSI) and a maximum of 125 PSI. The flow rate must be at least 3 gallons per minute (GPM). 3. Use a water softener if there is high mineral content in the water of your area. High mineral content causes excessive scale build-up in the coil/heat exchanger. 4. Un-roll the hose reel and then connect one end of the high pressure discharge

Consult factory for specific recommendations concerning chemicals and temperatures. 14. Only use original spare parts. 1. Before starting the pumps, follow all of the instructions in this manual and any supplemental instructions supplied with the pump. 1 1. A suction strainer should be attached to the suction hose or pipe. A suction strainer has holes or slots small enough to prevent large debris from working through and damaging the pump. Keep the strainer clean. If possible, suspend the st

Anchor block must be centered on beam and completely welded. 5. Install cylinder onto anchor block with the supplied pin and cotter pins. 6. Log stripper weldment can be welded to the beam or bolted to a 10-gauge (0.1345” thick) plate, which is welded to the beam. If welded to the beam, a 10-gauge spacer must be placed between the log stripper weldment and the beam to get the proper vertical height for the log stripper weldment. The log stripper weldment must rest against the cylinder face to