The button changes to Save. 3. Enter your MGP 464’s IP address and your domain name in the appropriate fields. (This information is available from your network administrator.) 4. If your MGP has a password assigned, enter it. 5. Click the Save button. To set up e-mail addresses for notification, do the following for each recipient of e-mail alerts: 1. Click the Edit button at the right end of the address row. The Edit button changes to Save. 2. Enter the e-mail address of the recipient, and the

P/2 DA4/DA6 Plus ......... Video output Number/signal type P/2 DA2 Plus .................. . P/2 DA4 Plus .................. . P/2 DA6 Plus .................. . Connectors ................................... . Nominal level ............................... Minimum/maximum levels -38.3dB @ 5 MHz -45dB @ 5 MHz 2 VGA-UXGA RGBHV, RGBS, RGsB, RsGsBs 4 VGA-UXGA RGBHV, RGBS, RGsB, RsGsBs 6 VGA-UXGA RGBHV, RGBS, RGsB, RsGsBs 2, 4, or 6 15-pin HD female (depending on the model) 0.7V p-p (excluding sync) P

4 lbs (1.8 kg) P/2 DA6 Plus ................... 5 lbs (2.3 kg) Vibration ....................................... ISTA/NSTA 1A in carton (International Safe Transit Association) Listings .......................................... UL, CUL Compliances ................................. CE MTBF ............................................. 30,000 hours Warranty ....................................... 3 years parts and labor Specifications are subject to change without Extron Electronics, USA 1230 Sou

6. Connect power to the distribution amplifier. 7. Power on the local monitor, the computer, and display device(s). Indicators and Controls Power LED: Located on the front and rear panels of the P/2 DA4 Plus and P/2 DA6 Plus only. When illuminated, it indicates that the distribution amplifier is receiving power. Video Gain toggle switch: (P/2 DA4 Plus and P/2 DA6 Plus only) The Video Gain switch is normally set to 0.7V (down). For installations with long output cable runs, the 1.0V (up) position

A 11 07 All trademarks mentioned in this manual are the properties of their respective owners. 1 Chapter One Introduction About the MTP 4T 15HD RS Twisted Pair (TP) Cable Advantages Introduction MTP 4T 15HD RS • Introduction MTP 4T 15HD RS • Introduction 1-2 1-3 C Do not connect this device to a computer data or telecommunications network. About the MTP 4T 15HD RS The Extron MTP 4T 15HD RS consists of four MTP T 15HD RS transmitters in a single enclosure. This set of transmitters and the Extron

They are available in singlemode or multimode versions. The analog audio signal(s) is (are) digitized in the transmitter, sent through the fiber cable, and converted back to analog audio in the receiver. These transceivers are class 1 laser products. They meet the safety regulations of IEC-60825, FDA 21, CFR 1040.10, and FDA 21 CFR 1040.11. Optical fiber interconnection between transmitter and receiver Number/type................................ 1 or 2 fiber optic Only one fiber is require

N This unit was tested with shielded cables on the peripheral devices. Shielded cables must be used with the unit to ensure compliance with FCC emissions limits. i HDMI 201 Tx/Rx • Table of Contents Table of Contents Chapter One • Introduction .....................................................1-1 About this Manual .....................................................................1-2 About the HDMI 201 Tx/Rx .....................................................1-2 TP cable advantages ......

The MHR-5P BNC cable is ideal for applications using red, green, blue, and separate horizontal and vertical sync outputs for connection to an Extron computer-video interface, switcher, distribution amplifier, or display device. The Extron MHR-5P BNC cable is NEC CL2P plenum-rated. For cable specifications, see page 705. MODEL VERSION DESCRIPTION PART # 3' (90 cm)................................................................................................. 26-378-01 6' (1.8 m)............

‘ Mir U » * _ __ '<) 1 ‘o;<; 'j H ® »à w MTP U R A MTP U R RS SEQ 1 VFfJSM * z (- ROB -- icttl ■*»»> •1 F.xtroo - XTP U R ns " MTP U R RS MTP U R RSA SEQ The MTP U Series Universal Receivers are designed to accept a wide range of video formats, along with RS-232 or audio signals, on a single UTP cable. When used with Extron MTPX and MTPX Plus Series matrix switchers, MTP U Series receivers eliminate the need for multiple receiver units and multiple cables per display, and

>80 dB at maximum output (unweighted) CMRR.............................................. 65 dB @ 20 Hz to 20 kHz Audio bits per sample.................. 18 bits per channel, 2 channels (L, R) Sampling rate ................................. 48 kHz Audio input — transmitter (FOX 500 DVI Tx) Number/signal type..................... 2 inputs (mixed): 1 balanced stereo; 1 unbalanced stereo or 2 unbalanced mono Connectors..................................... (1) 3.5 mm captive screw connector, 5