Votes - 5, Average rating: 4
(
)
)
|
manual abstract
The ESP/ALCI safety device is equipped with a test button so that its operation can be checked. TO USE (See Fig. A): 1. Press the reset button on the ESP /ALCI safety device. 2. Plug appliance into AC electrical outlet. 3. Then press the test button. The reset button will pop out. This verifies that the safety device is operating properly. Should the reset button not pop out, do not use the unit. Return immediately for service. 4. Press the reset button to re-activate the ESP /ALCI safety device and use the appliance. At any time, should this unit detect an electrical shock hazard, it will immediately shut off. To restore power, the reset button on the ESP /ALCI safety device must be pressed to reactivate the circuit. Repeat the above procedure each time this appliance is used to confirm that the safety device is operational. IMPORTANT: Never block air intake grille, as this will cause the unit to overheat. Should this happen, a built-in safety system will operate, and the unit will shut off automatically. At this point, turn the switch to Off and wait a while before attempting to operate appliance again. If the unit fails to operate after 10 minutes, it may indicate that the appliance has sustained extensive internal damage. Do not try to repair it yourself. Take it to an electrical service facility, or return it to the manufacturer. See warranty for instructions. CAUTION: Heating section should never be touched as it may be hot and burns may occur. To avoid possible scalp or hair burns, use very hot setting only when hair is wet. Reduce to lower heat as hair dries. Do not keep appliance directed at one place; keep it in constant motion. This is especially important if drying a wig, which could be damaged by heat. For maximum airflow, hold dryer no closer to the head than six inches. SPECIAL ATTENTION: This appliance is designed with a protective coating around the heating coils. During the first few minutes of initial use and immediately after the dryer is switched OFF, you may notice smoke and a slight odor. This is normal and will quickly disappear. This represents no danger to the user and does not indicate a defect in the unit. To extend the life of the dryer, it is advisable to switch it to the coolest setting for a few seconds before shutting it off. YOUR DRYER: This dryer features two speeds and three temperature settings. • High heat/speed for most styling/setting procedures and hair types. • Low heat/speed for "finishing" a hairstyle or for drying and styling permed, color-treated or fragile hair. • Cool setting, to set the style in place. HOW TO ADD/REMOVE ATTACHMENTS: Align attachment with track and slide along the track until it locks into place (See Fig. B). To remove slide attachment off of the track. DRYING AND DETANGLING 1. For initial drying use the High heat/speed setting. 2. As hair begins to dry attach the wide-tooth comb for detangling and continue drying. Use Low heat/speed for fragile, permed or color-treated hair. SHAPING-To add fullness and body to your hair: 1. Half-way dry hair, attach the thermal styling brush. 2. Set to the Low heat/speed setting. 3. Brush-dry your entire head of hair against its natural growth pattern, then brush-dry into place. 4. Stop when your hair is almost dry. STYLING -Both the thermal styling brush and fine-tooth comb attachments can be used for final styling. • Thermal styling brush – adds body, soft waves and smoothes out unruly hair. • Fine-tooth comb – adds height and fullness. HOW TO USE YOUR DUAL VOLTAGE DRYER For use in the U.S.A., the voltage selector should be in the 125-volt position. On 125 volts AC, you can use Low or High heat/speed or the Cool setting. When in the Cool setting it will have a reduced motor speed. For use in several countries overseas, the voltage selector may need to be placed in the 250-volt position. Confirm the voltage available at each overseas location before using the appliance. For connection to a 220-250 volt supply, use an attachment plug adapter of the proper configuration for the power supply receptacle. HOW TO CHANGE VOLTAGE NOTE: Be sure switch is in the Off position Use an appropriate instrument to move the voltage selector to the 125- or 250-volt setting. When using the 250-volt setting, this dryer will work only in the Low and Cool positions. When in the Low position it will be operating at High heat/speed. Do not, at any time, try to force the switch into the High heat/speed When in the Cool position it will have a reduced motor speed. CARE AND CLEANING This appliance is permanently lubricated and will not require additional lubrication for the life of the unit. It contains no user serviceable parts. Refer service to qualified service personnel. WHILE USING: Untwist cord from time to time to avoid tangling. TO CLEAN: Unplug unit and allow to cool. Use a soft, slightly damp cloth to wipe appliance surfaces. Do not allow water or any other liquid to get into the unit. Intake grille must be cleared of any bui...