This access hole must be plugged with a non-combustible insulation after the gas supply line has been installed. Si le foyer prefabrique ne comporte pas d’orifices d’amenee du gaz, un orifice d’au plus 37,5 mm (1,5 po) peut etre pratique, selon les regles de l’art, dans la partie inferieure des parois ou au fond de la chambre de combustion. Cet orifice doit etre obture au moyen d’isolant incombustible une fois la conduite de gaz en place. The installer must mechanically attach the marking suppli

Connect the wiring harness to the back of the receiver. 5. Install the Receiver in the Low Voltage Junction box, supplied with HZ54. 6. Insert the 4 AA type batteries in the battery compartment with the correct polarity. 7. Place the slider into the cover plate. 8. Put the Receiver switch in the “OFF” position, to allow correct lineup for slider switch. 9. Make sure the Receiver and cover plate words “ON” and “UP” are on the same side. 10. Align the slider with the switch on the Receiver and cou

Hampton Quality The rich, porcelain, enamel finish of each Hampton cast iron product is a work of art. Select the tasteful glass grill, one of four fashionable colors, side shelves, double screen doors and create your own Hampton. Exceptional Fire Without question, the Hampton fire is the best in the industry. Gas fires feature dancing flames and glowing embers, wood fires reveal the age old joy of the snap of wood as it catches fire and the curl of yellow flames from glowing embers. Cut Fuel Bi

The location of the termination cap must conform to the requirements in the Vent Terminal Locations diagram, see manual. FPI Direct Vent (Flex) System Termination Kits include all the parts needed to install the P33 using a fl exible vent. ImportantWhen installing Cabinet Mantels: the wall thimble must be secured first and venting must be attached to unit before sliding into final position. Snorkel Terminations Snorkel Terminations: FPI Kit # Length Contains: #946-513 2 Feet 1) 6-5/8” flexible l

This could cause high temperatures and may present the possibility of a fire. b) The location of the horizontal vent termination on an exterior wall must meet all local and national building codes, and must not be blocked or obstructed. See "Exterior Vent Termination Locations" section for more details. 7) Ensure that the pipe clearances to combustible materials are maintained (Diagram 5). Install the termination cap. Note: If installing termination on a vinyl siding covered wall, a vinyl siding

Wood Inserts ^R] EGENCY Wood Inserts FIREPLACE PRODUCTS I3100 Wood Insert I3100 Large Wood Insert Minimum Fireplace Opening Height 25” (635mm) Width 28” (711mm) Depth 17” (432mm) Faceplate Dimensions Standard 44” (wide) x 32” (height) Oversize 50” (wide) x 34.5” (height) Dimension Description I3100 A Adjacent Side Wall (to side) 13” (330mm) B Mantle (to top)** 19” (480mm) C Top Facing (to top) 18” (455mm) D Side Facing (to side) 6-1/2” (165mm) E Minimum Hearth Extension* 16”

1) Make sure the valve is in the "OFF" position. 2) Loosen the "IN" and/or "OUT" pressure tap(s), turning counterclockwise with a 1/8" wide flat screwdriver. 3) Attach manometer to "IN" and/or "OUT" pressure tap(s) using a 5/16" ID hose. G36D-NG1 System Data For 0 to 4500 feet altitude Burner Inlet Orifice Sizes: #42 Max. Input Rating 26,000 Btu/h Min. Input Rating 13,100 Btu/h Supply Pressure min.5.0" w.c. Manifold Pressure (High) 3.8"+/- 0.2"w.c. Log Set: Ceramic fibre, 7 per set. Vent System:

The pilot can be relit only Fireplace surround materials 5 5 Clearances ....................................... page llation .................................. page Preinstawhen fresh air is available. Refer to the Combustion and Ventilation Air section. Installation Applications stible) 5 6 Installation – Built-In ....................... page Dimensions........................ page FramingThe VF5000 and VF6000 Series Unvented Room Heaters may be built into a framed wall, or 1. Fireplace built i

If the ashes are to be disposed of by burial in soil or other wise locally dispersed, they should be retained in the closed container until all cinders have thoroughly cooled. SOFTWOOD VS HARDWOOD Softwoods contain about 15 percent highly flammable resin which generates creosote soot in the chimney flue. Burning softwood exclusively may not be as desirable nor as safe as burning denser hardwoods. Many experienced fire-builders use small amounts of softwood kindling and newspaper in conjunction w

(1.25 kPa) 12” W.C. (3.00 kPa) Manifold Pressure - High 3.8” W.C. (0.95 kPa) 11” W.C. (2.74 kPa) Manifold Pressure - Low 1.1” W.C. (0.27 kPa) 3.3” W.C. (0.82 kPa) Orifi ce Size #44 DMS - 0-2000ft #45 DMS - 2000-4500ft #54 DMS Minimum Input Altitude 0-2000 ft. (0-610m) 12,500 BTU/h (3.66 kW) 10,500 BTU/h (3.07 kW)Minimum Input Altitude 2000-4500 ft. (610-1372m) 10,500 BTU/h (3.07 kW) Maximum Input Altitude 0-2000 ft. (0-610m) 22,500 BTU/h (6.59 kW) 21,500 BTU/h (6.30 kW)Maximum Input Altitude 200