Clean with emery cloth or replace as required. 10. Verify millivolt output. Replace as necessary. Venting 1. Inspect venting for blockage or obstruction such as bird nests, leaves, etc. 2. Confirm that termination cap remains clear and unobstructed by plants, etc. 3. Verify that termination cap clearance to subsequent construction (building additions, decks, fences or sheds) has been maintained. 4. Inspect for corrosion or separation. 5. Verify weather stripping, sealing and flashing remains int

NOTES: 1Before cutting any holes check pipe manufacturers current instructions. 2Each pipe manufacturer has their own list of parts for kits. 3SL is not interchangeable with SLP. September 1, 2008 Quadra-Fire · Topaz · 7009-113G Page 47 Page 48 Quadra-Fire · Topaz · 7009-113G September 1, 2008 D. Service Parts List R TOPAZ (NG, LP) Exploded Parts Diagram Beginning Manufacturing Date: 12-8-03 Ending Manufacturing Date: Item # Description Item # Description Item # Description 1 Face Assembly, Quar

• By: Qualified Service Technician/Homeowner Be sure the appliance is allowed to cool, has been unplugged and the exhaust blower is off. The products of combustion will contain small particles of fly ash. The fly ash will collect in the exhaust venting system and restrict the flow of the flue gases. At start-up if there is incomplete combustion, or if there is a shutdown or incorrect operation of the appliance it will lead to some soot formation. This will collect in the exhaust venting system.

• Read, understand and follow these instructions for safe installation and operation. • Leave this manual with party responsible for use and operation. WARNING If the information in these instructions is not followed exactly, a fire may result causing property damage, personal injury, or death. WARNING HOT SURFACES! Glass and other surfaces are hot during operation and cool down. Hot glass will cause burns. • Do not touch glass until it is cooled • NEVER allow children to touch glass • Keep chil

September 1, 2008 Quadra-Fire · Topaz · 7009-113G Page 23 2. Valve Regulator Replacement WARNING Fire Risk. Explosion Risk. • Disconnect any electrical cords and turn off gas supply to unit before proceeding if converting fuel on an appliance already fully installed. Remove upper and lower back shield. Loosen the set col- Figure 6.6 Pull off pilot hood and set it aside. lars on the extension rods with the 3/32 in. Allen wrench. NOTE: Do not remove the retaining clip from the hood. Remove the rod

i • 6/09 1 Model(s): QVI30S QVI35S • Do not store or use gasoline or other fl ammable vapors and liquids in the vicinity of this or any other appliance. • What to do if you smell gas - Do not try to light any appliance - Do not touch any electrical switch. Do not use any phone in your building. - Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions. - If you cannot reach your gas supplier, call the fi re department. • Installation and service must be

Failure to follow these instructions could result in property damage, bodily injury or even death. • Do not store or use gasoline or other fl ammable vapors and liquids in the vicinity of this or any other appliance. • Do not overfi re - If any external part starts to glow, you are overfi ring. Reduce feed rate. Overfi ring will void your warranty. • Comply with all minimum clearances to combustibles as specifi ed. Failure to comply may cause house fi re. Check building codes prior to installati

Figure 6.3 Minimum Clearances for Termination CAUTION: IF EXTERIOR WALLS ARE FINISHED WITH VINYL SIDING, IT IS SUGGESTED THAT A VINYL PROTECTOR KIT BE INSTALLED. WARNING! In the U.S.: Vent system termination is NOT permitted in screened porches. You must follow side wall, overhang and ground clearances as stated in the instructions. In Canada: Vent system termination is NOT permitted in screened porches. Vent system termination is permitted in porch areas with two or more sides open. You must fo

NOTE: Clearances may only be reduced by means approved by the regulatory authority having jurisdiction. WE RECOMMEND that you have a qualified building inspector and your insurance company representative review your plans before and after installation. Thermal Conductivity: k value The k value indicates the amount of heat (in BTU’s) that will flow in 1 hour through 1 square foot of a uniform material 1 inch thick for each degree (F) of temperature difference from one side of the material to the

B • 12/08 7 77 Installation Preparation Prepare the existing solid fuel masonry or factory built non-combustible firebox for installation. A. Inspection and Cleaning Prior to installing the gas insert: • Have the chimney and adjacent structure inspected and cleaned by qualified professionals. Hearth & Home Technologies recommends that NFI or CSIA certified professionals, or technicians under the direction of certified professionals, conduct a minimum of a NFPA 211 Level 2 inspection of the chimn