first 24 hours. Put the cover on and allow the spa to heat to desired 17. temperature. Adjusting The Proper Bromine Levels After start up, decrease the filtration cycle to F-4 1. and monitor the bromine level until it is within the recommended range. Use bromine test strips to achieve a 3-5 ppm 2. recommended level. Note: It can take several days for the bromine level to stabilize because the fill water that was used sometimes contains contaminants that need to be neutralized, thereby using up t

All rights reserved. Duplication without written consent is strictly prohibited. Cal Spas® is a registered trademark. Due to continuous improvement programs, all models, operation, and/or specifications are subject to change without prior notice. LTR20081024, Rev. B 6/12/08 CONTACT INFORMATION For customer service, please contact your authorized dealer immediately. If you need additional information and/or assistance, please contact: L.M.S. Customer Service Department 1462 East Ninth Street Pomo

out. Place the dirty filter into a bucket of water deep enough to cover the filter. Add 8 oz of Cal Spas “Liquid 2. Filter Cleaner” to the bucket of water. Note: It is a good idea to keep a spare filter to use in the spa while the dirty filter is being deep cleaned. This way, you can rotate the filters and both will last longer. Twist off the tablet tube and set it aside3. Soak the filter for a minimum of 24 hours.4. Spray the filter with a water hose. Spray each pleat carefully.5. Put fresh bro

The panel will display “TEMP LOCK” when the set temperature is locked. To unlock the set temperature: Press the “UP” or “DOWN” button, “TIME”, “JETS 1”, and then the “DOWN” button. Circulation Pump This is an optional feature. The circulation pump will come on when the system is checking temperature, during filter cycles, during freeze conditions, or when another pump is on. Preset Filter Cycles There are two filter cycles per day. The start and end times of each cycle are programmable. To progr

(Displays on third occurrence of dr message.) Spa is shut down. Follow action required for dr message. Spa will not automatically reset; you may press any button to reset. Pr When your spa is first actuated, it will go into priming mode. The priming mode will last for up to four minutes and then the spa will begin to heat and maintain the water temperature in the Standard mode. --F or --C Temperature unknown After the pump has been running for two minutes, the temperature will be displayed. - -

When installing and assembling your surround package, it is recommended that two or more people be involved. Do not use the unit during an electrical storm. Do not climb on top of the surround package. While the surround package is made out of high-quality material and is extremely durable, it is not meant to support weight. In addition, falling off of the surround package while climbing on it can result in serious injury or death. Do not attempt any repair without consulting the manufacturer fi

Light niche and any metallic items in a 5’ (152 cm) radius must be properly bonded with #8 AWG grounding wire. Connect rigid conduit to the 3/4” hub located at the back of the light 1. niche and run to a water resistant junction box (or for 12 volt models to a low voltage transformer) no further than 25’ (7.6m). Remember this is a water cooled light, so the conduit and all connections must be leakproof. Feed the light cord through the rigid conduit to the junction box, leaving 2. at least 4 feet

Due to our continuous improvements, specifications, size and pricing are subject to change without prior notice. Avalon Series Model Width Length Depth Gallons Dry Weight Filled Weight A726B 84” 84” 39 1/2” 425 850 Lbs. 4390 Lbs. A726L 84” 84” 39 1/2” 425 850 Lbs. 4390 Lbs. A744B 84” 84” 39 1/2” 425 850 Lbs. 4390 Lbs. A744L 84” 84” 39 1/2” 425 850 Lbs. 4390 Lbs. A826B 93” 93” 39 1/2” 450 900 Lbs. 4648 Lbs. A826L 93” 93” 39 1/2” 450 900 Lbs. 4648 Lbs. A844B 93” 93” 39 1/2” 450 900 Lbs. 4648 Lbs.

Make sure the spa is positioned so that access to the equipment compartment and all side panels will not be blocked. Be certain that your installation will meet all city and local safety codes and requirements. Consider how you will use your spa How you intend to use your spa will help you determine where you should position it. For example, will you use your spa for recreational or therapeutic purposes? If your spa is mainly used for family recreation, be sure to leave plenty of room around it

If the area receives direct sunlight, you will want to provide some • protection for the equipment portion of the equipment pack. The equipment pack and heater are delivered separately. Do not cover gas heaters unless properly vented. (See heater owner’s manual for important safety information.) Portable Spa Site Preparation Your spa needs a solid and level foundation. The area that it sits on must be able to support the weight of the spa, with water and the occupants who use it. If the foundati