5. Ensure the Tractor is equipped with a functional ROPS and seat belt and require that the employee operator securely fasten the safety belt and operate with the ROPS in the raised position at all times. 6. Forbid the employee operator to carry additional riders on the Tractor or Implement. 7. Provide the required tools to maintain the Tractor and Implement in a good safe working condition and provide the necessary support devices to secure the equipment safely while performing repairs and serv

(SG-21) 9.1 Tractor Pre-Operation Inspection/Service Refer to the tractor operator’s manual to ensure a complete pre-operation inspection and scheduled service is performed according to the manufacturers recommendations. The following are some of the items that require daily service and inspection: • Tire condition/air pressure • Wheel lug bolts • Steering linkage • PTO shield • SMV sign is clean and visible • Tractor’s lights are clean and functional • Tractor Seat belt is in good condition • T

Remove point from welded tooth shank by hammering at “A” on tooth point or by driving a chisel at “B”, just between tooth point box section and tooth shank. Install new point and anchor it to shank by peening at location shown. It a tooth shank breaks off, becoming lost or damaged so that is cannot hold a tooth point, a new shank should be welded to bucket. TIGHTENING NUTS AND BOLTS Periodically check to be sure all bolts and nuts are tight (See Torque Chart). Check all pivot pins for cotter pin

(STI-4) Lift-Type Mower -To disconnect the mower, first extend the tractor 3-point hitch top link to remove tension on the top link hitch pin. When the pin is loose and easy to rotate, remove the pin from the mower. Next remove both lower hitch pins. Semi-Mount Mower-To disconnect the mower, first remove hydraulic pressure by moving the control lever back and forth several times. Next remove both lower lift arms and the hydraulic hose. Pull-Type Mower - To disconnect the mower, first relieve hyd

2. Place lifting device (scissors jack, hydraulic jack) under center of cutter housing. 3. Remove hex nuts, washers and carriage bolts from bracket at each end of roller. Make certain that roller bracket is free to move once the fasteners are removed. A stuck roller could drop suddenly and cause and injury. 4. Use lifting device to reposition cutter housing to desired cutting height. Align bracket holes with cutterhousing holes, then reinstall fasteners. Refer to cutting height decal on mower or

NOTE: Where there are grass and weeds high enough to hide debris that could be struck by the blades, the area should be: inspected and large debris removed, mowed at an intermediate height, inspected, closely with any remaining debris being removed, and mowed again at desired final height. (This will also reduce power required to mow, reduce wear and tear on the Mower drivetrain, spread cut material better, reduce streaking, and make the final cut more uniform). (SRM-1) Do Not attempt to raise o

Parts Section -6 AXLE HYD SCHEMATIC - LEVEL LIFT OPTION Hydro 10 and 15 ft (08-05) Rev 01-08 ©2008 Alamo Group Inc. Parts Section -7 AXLE HYD SCHEMATIC - LEVEL LIFT OPTION Continued... ITEM PART NO. QTY. DESCRIPTION 1 8719B 1 CYL. ASY, 3-1/2" BORE (CNTR AXLE) 2 8720B 1 CYL. ASY, 3-1/4" BORE (RH WG AXLE) 3 7521B 1 CYL. ASY, 3" BORE (LH WG AXLE) 4 02965360 1 HOSE ASY, #6 - 6FJX - 6FJX - 202" LG 5 02981345 1 HOSE ASY, #6 - 6FJX - 6 FJX - 192" LG 02979578 1 HOSE ASY, #6 - 6FJX - 6FJX - 166" LG 6 029

Never operate the tractor at speeds that cannot be safely handled or which will prevent the operator from stopping quickly during an emergency. If the power steering or engine ceases operating, stop the tractor immediately as the tractor will be difficult to control. Perform turns with the tractor and mower at slow speeds to determine how the tractor with and attached implement handles a turn. Determine the safe speed to maintain proper control of the tractor when making turns. When turning with

Parts Section -43 REVERSER FAN KIT (NEW MEXICO) ITEM PART NO. QTY. DESCRIPTION 1 02986772 1 REVERSER TIMED FAN CONTROL 2 02987287 1 FAN REVERSER MOUNT 3 00752735 4 SELF TAP 5/16 NC 3/4 PL FALCON 10 and 15 09-08 ©2008 Alamo Group Inc. Parts Section -44 THIS PAGE INTENTIONAL LEFT BLANK FALCON 10 and 15 09-08 ©2008 Alamo Group Inc. Parts Section -45 SIDE SKIRTS AND SKID SHOES FALCON 10 and 15 09-08 ©2008 Alamo Group Inc. Parts Section -46 SIDE SKIRTS AND SKID SHOES Continued... ITEM PART NO. QTY. D

6. Do not permit others to ride. 7. Operate the tractor smoothly, no jerky turns, starts, or stops. 8. Hitch only to the draw bar and hitch points recommended by the tractor manufacturer. 9. When the tractor is stopped, set brakes securely and use park lock, if available. Keep children away from danger all day, every day... Equip tractors with rollover protection (ROPS) and keep all machinery guards in place... Please work, drive, play and live each day with care and concern for your safety and