CABLEASSEMBLY (90) through openings in BASE (10) as shown in FIGURE 1. • Securely assemble two 3-1/2" PULLEYS (79) into BASE (10) using two 3/8 X 2-3/4" BOLTS (38), four 3/8" FLANGE SPACERS (66), and two 3/8” LOCKNUTS (48). (NOTE: Make sure LEG EXT. CABLE ASSEMBLY (90) is routed under PULLEYS and BOLTS.) • Slide LEG EXT. CABLE ASSEMBLY (90) through the opening in the end of the BASE (10) as shown in FIGURE 1. • Insert four 3/4" FLANGE BEARINGS (69) into tubes on REAR UPRIGHT (16) as shown in
ALL CONNECTIONS WILL CONSIST OF ONE m BOLT. TWO (2) WASHERS. AND ONE (1) LOCK NUT. NOTE: BOLT LENGTH IS MEASURED FROM THE UNDERSIDE OF THE HEAD OF THE BOLT. lllllll = I-BOLT LENGTH- BOLT LENGTH RULER: 425 Parts List 1 KEY PART # DESCRIPTION QTY KEY PART # DESCRIPTION QTY 1 6571603 PRESS BASE WHT 1 59 6218401 BRKT PULLEY 3 1/2 X 1 BLK ZN 1 2 6530603 PRESS ARM WHT 1 60 6321201 LEVER CONTROL 1 3 6529303 PRESS BACK SUPPORT WHT 1 61 6427101 CLEVIS KEYHOLE 3 4 6529003 CALF/LOW RO
No pretense here. Just all the variety, durability, and performance you need to get the job done. It's as simple as that. Club-quality equipment that's built to last. These machines deliver the kind of free weight workout your body craves. Don't let the equipment you use limit your strength-training regimen. Get the equipment that works just as hard as you do. With the Free Weight Smith System and a full range of specialized workout stations to choose from, you can't go wrong with ParaBody. 2
BOLT............................................................................................................. 2 2. 3/8 X 3 IN. BOLT................................................................................................................. 14 3. 3/8 X 2-3/4 IN. BOLT............................................................................................................. 1 4. 3/8 X 2 IN. BOLT ..........................................................................................
8. Identify the Left Pedal Arm (14), which is marked with a sticker that has an “L” on it. Make sure that there are two Pedal Arm Bushings (33) in the Left Pedal Arm. Apply a thin film of the included grease to a Pedal Axle (34). Insert the Pedal Axle into the Left Pedal Arm, and slide a Pedal Washer (32) onto the Pedal Axle. Firmly tighten the Pedal Axle into the Crank (30). Tighten a 1/2” Nylon Locknut (35) onto the end of the Pedal Axle protruding from the Crank. Make sure that there are two
STEP 13: FIGURE 13 • Assemble one 3-1/2” PULLEY (24) into PRIMARY PIVOT (9) upper hole using one 3/8 X 8” BOLT (31), two 3/8” FLAT WASHERS (36), two 3/8 X 1-3/16” SPACERS (44) and one 3/8” LOCK NUT (34) and tighten securely • Assemble two 3-1/2” PULLEYS (24) into FRAME (1) using two 3/8 X 3-3/4” BOLTS (30), four 3/8 X 1-1/16” FLANGE SPACERS (42) and two 3/8” LOCK NUTS (34) and tighten securely. 9 34 36 24 42 44 31 30 1 3/8 X 3-3/4” 3/8 X 8” 16 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2 FIGURE 14 • Re
Consult your physician before beginning any exercise program. 2. Inspect equipment daily. Tighten all loose connections and replace worn parts immediately. Failure to do so may result in serious injury. 3. Do not allow minors or children to play on or around this equipment. 4. Exercise with care to avoid injury. 5. If unsure of proper use of equipment, call your local Parabody distributor or call the Parabody customer service department at (800) 328-9714. Please note: * Thank you for purchasing
FOR 220 GYM SYSTEM Version: 221101 TABLE OF CONTENTS Safety Statement.............2 General Notes..................3 Tools Required................3 Gym Layout.....................4 Parts list..........................5 Assembly Instructions.....5-10 General Maintenance.......11 Warranty Statement..........12 Product Services..............13 Insert-Registration Card IMPORTANT SAFETY INFORMATION THERE IS A RISK ASSUMED BY INDIVIDUALS WHO USE THIS TYPE OF EQUIPMENT. TO MINIMIZE RISK FOLLOW THESE R
BOLT, one (1) 2-3/8 IN. CABLE RETAINING CLIP, and one (1)3/8 IN. LOCK NUT. - . LOOSELY assemble one (1) 3-1/2 X 1 IN. PULLEY to the middle pulley flat of the 350 BASE using one (1) 3/8 x 2 IN. BOLT, one (1) 2-3/8 IN. CABLE RETAINING CLIP, and one (1) 3/8 IN. LOCK NUT. SECURELY attach the BASE CONNECTION WELDMENT and the 832 to the base of the 350 using two (2) 3/8 X 3 IN. BOLTS, four (4) 3/8 IN. WASHERS, and two (2) 3/8 IN. LOCK NUT S. Following the cable routing diagram, thread the LEG PRESS
Please read these instructions thoroughly and keep them for future reference. This product must be assembled on a flat, level surface to assure its proper function. * We recommend cleaning your product (pads and frame) on a regular basis, using warm soapy water. Touch-up paint can be purchased from your Parabody customer service representative at (800) 328-9714. There is a risk assumed by individuals who use this type of equipment. To minimize risk, please follow these rules: 1. Inspect equip