This applies in particular to trademarks, model denominations, part numbers and drawings. This instruction book meets the requirements for instructions specified by the machinery directive 98/37/EC and is valid for CE as well as non-CE labelled machines. Note: The PED instructions for this machine are included at the end of the book. No. 2920 1521 00 Registration code: APC SF / 38 / 980 2003-10 2920 1521 00 1 Instruction book This instruction book describes how to handle the machines to ensure s

If your locomotives and cars use more then 2.5 Amps, it is necessary to split the layout in several power sections and feed each section with an extra "booster" which provides more amperage. Terminals C & D on your Commander can be used to wire in extra boosters. For more information about adding power stations to your layout, please see the DCC section of Atlas' web site at LIMITED ONE-YEAR WARRANTY Atlas Model Railroad Company, Inc. warrants that this Commander will be free from defects in mat

com1- 800- 633- 0405AATTLLAASSINDUSTRIALFLATPANELPC MONITORQUICKINSTALLATIONGUIDE-ATM1700/ATM1700T 3505HUTCHINSONROADCUMMING,GA30040-5860,USA TM 1. Verify Contents of the Box: •AtlasFlatPanelMonitor–ATM1700orATM1700T(The“T”attheendofthepartnumberdesignatesthetouchscreenoption.) •VGAvideocable–6’length•RS-232Serialtouchscreencable(ATM1700Tonly)–6’length•USBtouchscreencable(ATM1700Tonly)–2mlength•Mountingclipsandscrews(qtyof14) •USBretentionbracketandmountingscrew(ATM1700T only) •DocumentationandD

9. Adjust the Monitor OSD Settings as Required•PresstheSelect(AutoAdj)controlbuttonontherearofthepaneltoinitiateanautomaticconfigurationofthescreen. •Althoughnormallynotneeded,thecontrolbuttonsontherearofpanelcanbeusedtomakeotheradjustmentstothescreen. •ConsulttheHardwareUser’sGuide,ATM-19-USER,onthesuppliedDocumentationandDriveCDfordetailedusageoftheOSDsettings. 10. Installation Complete TOP VIEWFRONT VIEWADC P.N. ATM-AC-CON orPHOENIX CONTACT P.N. 1777992L NPlug Retention ScrewsPowerConnectionL

... . . ....... . . . . ©Copyright 2005 ATLAS COPCO CONSTRUCTION TOOLS AB 2005-06 NACKA • SWEDEN No 3392 5042 01 1 English ! . INTRODUCTION ....................................................................................................................... 2 SAFETY INSTRUCTIONS ........................................................................................................ 2 Introduction to safety ...........................................................................

. Walk through the coverage Ball area noting where you are Joint when the lights turn on. Move the sensor head up, down, or sideways to change the coverage area. Keep the sensor at least 1" (2.5 cm) away from the lamps. . Adjust the RANGE as needed. RANGE set too high may increase false triggering. . Secure the sensor head by tightening the clamp screw. Do not overtighten the screw. . Set the amount of ON-TIME you want the lights to stay on Aim Sensor Down for Short Coverage Aim Sensor Higher fo

• Automatically controls existing post light. • Dual Light Level. • Photocell keeps the light off during daylight hours. This package includes: Post Light Adapter 3 Screws 3 Wire Connectors Requirements • The Light Control requires 120 volts AC. • If you want to use Manual Override, the control must be wired through a switch. • Some codes require installation by a qualified electrician. OPERATION Mode: On-Time Works: Day Night Test 5 Sec x x Auto 1, 5, or 20 Min x Manual To Dawn* x Accent 3,6 Hr

(1 m). Sensor Least Sensitive . Loosen the clamp screw in the sensor ball joint and gently rotate the sensor. . Walk through the coverage area noting where you are when the lights turn on (also, the LED will flash several times whenmotionisdetected).Move the sensor head up, down, or sideways to change the coverage area. Keep the sensor at least 1" (25 mm) away from the bulbs. Most Sensitive Clamp Screw Ball Joint Aim Sensor Down for Short Coverage 4 598-1098-02 SPECIFICATIONS Range ............

• Automatically turns lighting off. • Photocell keeps the lighting off during daylight hours. • LED indicates motion was sensed (day or night). Requirements • The Light Control requires 120-volts AC. • If you want to use Manual Mode, the control must be wired through a switch. • Some codes require installation by a qualified electrician. OPERATION Mode: On-Time: Works: Day Night Test 5 Sec x x Auto 1, 5, 10 min. x Manual Until Dawn* x * resets to Auto Mode at dawn. Note: When first turned on wai

Features • Turns on lighting when motion is detected. • Automatically turns lighting off. • Photocell keeps the lighting off during daylight hours. • LED indicates motion was sensed (day or night). This package includes: Bulb Holders Rubber Plug Plastic Hanger Cover Plate Sensor 2 Wire Connectors Mounting Bolt Mounting Strap Gasket 6 Screws (3 sizes included) Light Control Requirements • The light control requires 120-volts AC. • If you want to use Manual Mode, the control must be wired through