(102 mm) 6 in. (152 mm) 7 in. (177.8 mm) 8 in. (203 mm) 10 in. (203 mm) 12 in. (305 mm) Table 4 9001000 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 45 Installation Water Connection WARNING To avoid personal injury, recommended inlet water temperature should be nohigher than 125° Fahrenheit (51° Celsius). W709 The 18-135 models are delivered with hoses with 3/4 inch hose connectors. The 165 model is delivered with 3 x 1 inch and 1 x 3/4 inch hose connectors. These hoses fi
3 Nameplate Location.............................................................................. 4 General Inspection................................................................................ 5 Storage .................................................................................................. 5 PowerFlex 40 and 400 Drive Control Logic ..................................... 6 Installation/Wiring................................................................................ 6 Input
(If this tumbler changes ownership, be sure this manual accompanies the tumbler.) Installation/ Part No. M414545 September 2002 TABLE OF CONTENTS SECTION I Safety Important Safety Instructions. . . . . . . . . . . . . . . . . . 5 SECTION II Introduction Information for Handy Reference . . . . . . . . . . . . . . 7 Parts Ordering Information . . . . . . . . . . . . . . . . . . . 8 Nameplate Location . . . . . . . . . . . . . . . . . . . . . . . . . 8 Roughing-In Dimensions and Specifications Cabi
All but three cycles use the standard wash agitation. This agitation repeats for the first programmed time duration in the prewash, wash, and fill segments. The standard wash agitation sequence: . 12 seconds counterclockwise at wash speed . A 3-second pause . 12 seconds clockwise at wash speed . A 3-second pause Note: While a cycle is in progress, pressing and holding the Start key will cause the current cycle number to be displayed. Pressing and holding the Up key while a cycle is running will
28. Failure to install, maintain, and/or operate this washer according to the manufacturer’s instructions may result in conditions which can produce bodily injury and/or property damage. NOTE: The WARNINGS and IMPORTANT SAFETY INSTRUCTIONS appearing in this manual are not meant to cover all possible conditions and situations that may occur. Common sense, caution and care must be exercised when installing, maintaining, or operating the washer. Any problems or conditions not understood should be r
Operating the machine with severe out-of-balance loads could result in personal injury and serious equipment damage. SW039 9001000 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 5 Introduction Model Identification Information in this manual is applicable to these models: HX18PVQM6 SX18PVPA7 UX18PVNA6 HX18PVQU6 SX18PVQU6 UX18PVNU6 HX18PVQM7 SX18PVQM6 UX18PVNA7 HX18PVXU6 SX18PVXU6 UX18PVPU6 HX18PVXM6 SX18PVQM7 UX18PVPA6 UX18PVQU6 HX18PVXM7 SX18PVXM6 UX18PVPA7 UX18PVXU6 SX18PVX
Refer to the INSTALLATION INSTRUCTIONS for details of proper washer installation. IMPORTANT: Prior to first wash, use an all purpose cleaner, or a detergent and water solution, and a damp cloth to remove shipping dust from inside of wash drum. 1. Get the clothes ready for washing. Empty pockets and cuffs. Sort items into separate loads. Pretreat stains and heavily soiled areas. TLW1991N IMPORTANT: Remove all sharp objects from laundry to avoid tears and rips to items during normal machine operat
Refer to Figure 6. NOTE: End of drain hose must be below 24 in. (61 cm). Laundry Tub Installation: For this type of installation, the drain hose MUST be secured to the stationary tub to prevent hose from dislodging during use. Refer to Figure 7. Use the beaded strap (supplied in accessories bag) to secure hose. H023I 1 Drain Hose 2 Beaded Strap (tape if necessary) 3 Fill Hoses Figure 6 3 1 2 SWD600N 1 Drain Hose 2 Tie-Down Strap (tape if necessary) Figure 7 SWD600N 1 2 Step 4: (Gas Dryer Only) C
Failure to do socan cause buildup of pressure and risk a tubing rupture. W491 50 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 9001000 Installation Steam Requirements For washer-extractors equipped with optional steam heat, install piping in accordance with approved (Steam Heat Option Only) commercial steam practices. Steam requirements are shown in Table 7. WARNING Never touch internal or external steam pipes, connections, or components. These surfaces can be extremely hot
- teasting in lab.) 80 kW............................. 1GG PSIG (б.9 bar) Max. 1G.4 (7.7б kW) 7.87 (5.88 kW) 9.5 (5.88 kW) (2) 4G-1/2”L x 15-3/4”H x (2) (1G29 mm x 4G1 mm x 153 mm) 3/4” (2G mm) (DN2G) (2) 3/4” (2G mm) (DN2G) 3/4” (2G mm) (DN2G) 110 lb. (49.9 kg) Indian Head cloth 70% water retention - 31 min. 50% water retention - 23 min. Rated Heater Input Heater Amps, Motor Amps, Control Amps, Total Amperes at Rated Voltage HZ Minimum Size Supply Wire Based on 75° C (167 F) Insula