Login: 270 sec.) CT-S801 - High performance • Print speed: 300mm/sec (11.8 IPS) • fastest in its class • newly developed gate array • 32 bit RISC CPU a • 8MB SDRAM t • Resolution: 203 DPI (8 dots/mm) ' • high quality printing • smooth graphics • more characters/line CT-S801 - More features • Head Pressure Adjustment Lever Paper thickness from 65 - 150 pm • Integrated Buzzer • Standard & 2D Barcodes • Paper “near-end” detection • Updated mechanical sensor • Improved accuracy • Reduces
¦ In case of trouble do not attempt to repair the printer. Ask Citizen Systems service for repair. ¦ Be careful that the printer cover does not entrap your hands or fingers. ¦ Be careful with sharp edges on the printer. Do not allow them to injure you or damage property. •May result in electric shock, burn, or injury. If the printer emits smoke, an odd smell, or unusual noise while printing, immediately abort the current print session and unplug the printer from the supply outlet. DAILY MAINTENA
1.00 - 9 - SRP-350II 1-2-3 USB Interface USB IFG-U TYPE Drawer kick-out connector Power supply connector USB connector Pin No. Signal Name Assignment (Color) Function Shell Shield Drain Wire Frame Ground 1 VBUS Red Host Power : DC5[V] / 500[mA] 2 D-White Differential Data Line 3 D+ Green Differential Data Line 4 GND Black Signal Ground 1-3 Connecting the Drawer . WARNING Use a drawer that matches the printer specification. Using an improper drawer may damage the drawer as well as the printer. .
270mm (63.82 Lines/sec, 1/6inch feed) • 2color Max. 130mm (30.73 Lines/sec, 1/6inch feed) • Ladder Barcode: Mono 270mm/sec, 2Color 130mm/sec Paper feeding Speed • Approx. 270mm/sec Table 3-2 Thermal Printer Specification 2) 203 dpi Item Description Remark Model • SRP-F312 (TPH: KRC-80-8TA02-BIX2,KYOCERA CORPORATION) Print Method • Thermal Line Printing Dot Density • 0.125mm(8 Dots/mm) Printing Direction • Uni-direction with friction feed Printing Width •80.0mm, 640 dot Position Character / Line
The changed set value is printed. (When change of set value is repeated, the original set value is recovered). When you press the FEED button long, the set value is accepted and then the printer goes to the next setting item. 5. Returning to the memory switch select mode When the setting of the desired content is completed, open the printer cover and then close the printer cover. This allows the printer to print the setting of the changed memory switch. 6. Saving the setting and exiting the memo
. Battery replacement SR-270II is powered by two alkaline batteries (GP76A). If the display becomes dim and difficult to read, the batteries should be replaced as soon as possible. To replace batteries : 1) Remove the screws and the back cover. 2) Replace the old batteries and install new ones with polarity in correct directions, then secure the screws in place and press [ ON/AC ] to turn the power on. . Auto power-off function This calculator automatically turns it off when not operated for app
11 1-4-2 Parallel & USB2.0 Interface........................................................................11 1-4-3 Auto Cutter Enable / Disable selection .......................................................12 1-5 Setting the Memory Switches .................................................................................13 1-6 Installing or Replacing the Paper Roll.....................................................................16 1-7 Adjustments and Settings............................
The actual output from the printer is "vertically reversed" due to the way the printer outputs the menu options. Please look at the example below to see how the output changes. Menu Setting Flow Chart (p.32) Menu Setting Flow Chart (p.32) Mode Settings
Set the media roll and media holder in to the printer as shown above. It is advisable to pull a length of media forwards and through the mechanism ready for later positioning. 5. Move the media roll so it is touching the left side of the housing. Then slide the black movable media guide so it is touching the media on the right side. Note: Do not try to hold the media too tightly with these guides as it will cause the printer to jam during printing. 6. Align the media with the left fixed media gu
Cut Counter – – Displays the cut count. Sensor Monitor – *.* V Displays the sensor level. Option Interface [Option I/F] – None LAN Displays the presence/absence of the optional interface. Test Mode Print Pattern Current Config Current Config Global Config Sample Executes the test pattern. Head Check No Yes Executes head check. No Factory Default No Yes No Initializes the set values of the configuration set to the state when the unit was shipped from the factory. Hex Dump No Yes No Sets the hex d
