Login:
Sorted: Name ↑   Downloads   Rate   Size ↑  

Northern Industrial Tools 142264

downloaded: 3File size: 2 mb    Manafacture: Northern Industrial Tools  
Category: Home Care Products

Failure to follow the safety rules and other basic safety precautions may result in serious personal injury. Item#142264 Thank you very much for choosing a NORTHERN TOOL + EQUIPMENT CO., INC. Product! For future reference, please complete the owner’s record below: Model: _______________ Purchase Date: _______________ Save the receipt, warranty and these instructions. It is important that you read the entire manual to become familiar with this product before you begin using it. This machine is de

Northern Industrial Tools 150611

downloaded: 6File size: 2 mb    Manafacture: Northern Industrial Tools  
Category: Power Screwdrivers and Drills

11. 8 PRODUCT FEATURES 1. WARNING! NOTE: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram on page 13. Always make sure the Rocker Switch (39) of the Impact Wrench is in its “OFF” position and the tool is unplugged from its electrical outlet prior to making any adjustments to the tool. (See Figure D.) Note: When your finger is off the Rocker Switch (39), the tool is in the “OFF” position. 2. Rocker Switch (39): The Rocker Switch is operat

Northern Industrial Tools 9564CV

downloaded: 1File size: 223 kb    Manafacture: Northern Industrial Tools  
Category: Sanders

Higher speed is obtained when the dial is turned in the direction of number 5. And lower speed is obtained when it is turned in the direction of number 1. Refer to the table below for the relationship between the number settings on the dial and the approximate rotating speed. RPM (/min) 1 2,800 | | 2 4,000 | | 3 6,500 | | 4 9,000 | | 5 10,500 CAUTION: • If the tool is operated continuously at low speeds for a long time, the motor will get overloaded and heated up. • The speed adjusting dial can

Northern Industrial Tools 6217D

downloaded: 0File size: 167 kb    Manafacture: Northern Industrial Tools  
Category: Power Screwdrivers and Drills

• A stuck bit can be removed simply by setting the reversing switch to reverse rotation in order to back out. However, the tool may back out abruptly if you do not hold it firmly. MAINTENANCE 001145 1 1. Limit mark 001903 1 2 1. Brush holder cap 2. Screwdriver • Always secure small workpieces in a vise or similar hold- down device. • If the tool is operated continuously until the battery cartridge has discharged, allow the tool to rest for 15 minutes before proceeding with a fresh battery. CAUTI

Northern Industrial Tools 180250

downloaded: 2File size: 8 mb    Manafacture: Northern Industrial Tools  
Category: Garden Tools

Mower not level side to side, uncut or partially cut grass. 2. Blades dull or bent. 3.Carrier RPM too low. 4. Field conditions are so wet that the tractor tire is pushing grass into mud. 5. Ground speed too fast. 6. Blades lock back. 7. Blades riding up due to blade bolt wear or loose bolts. 8. Grass is down from previous weather conditions, 9. Possible build up of marerial under mower. Level 3 pt. Hitch linkage on tractor. Sharpen or replace blades. Use correct PTO speed. Too wet to

Northern Industrial Tools M35982E

downloaded: 8File size: 206 kb    Manafacture: Northern Industrial Tools  
Category: Water and Air Pumps

Use this product properly and enjoy the benefits from its high performance. By purchasing a NorthStar product, you show a desire for quality and durability. Like all mechanical equipment this unit requires a due amount of care. Treat this unit like the high quality piece of machinery it is. Neglect and improper handling may impair its performance. Please thoroughly read the instructions and understand the operation before using your product. Limited Warranty NorthStar shall warranty any piece of

Northern Industrial Tools M157300E

downloaded: 7File size: 782 kb    Manafacture: Northern Industrial Tools  
Category: Pressure Washers

(Cat Pumps) - Remove shipping plug and install vented fill cap. (Comet Pumps) - See pump oil cap section of this manual. Closely inspect all components. -If you have damaged components: Contact the freight company that delivered the unit and file a claim. -If you have missing components: Contact Customer Service at 1-800-270-0810. Read this manual. Serious injury or death can result if safety instructions are not followed. WARNING M157300E Owner’s Manual Pressure Washer: Machine that cleans dirt

Northern Industrial Tools 9524NB

downloaded: 1File size: 179 kb    Manafacture: Northern Industrial Tools  
Category: Sanders

1 2 3 9523NBH 1 2 3 9523NBH Wheel guard 2. Bearing box 3. Screw 001060 Installing or removing wheel guard CAUTION: • When using a depressed center grinding wheel/Multidisc, flex wheel, wire wheel brush or cut-off wheel, the wheel guard must be fitted on the tool so that the closed side of the guard always points toward the operator. Mount the wheel guard with the protrusion on the wheel guard band aligned with the notch on the bearing box. Then rotate the wheel guard around 180 degrees. Be sure

Northern Industrial Tools 112020

downloaded: 0File size: 412 kb    Manafacture: Northern Industrial Tools  
Category: Nail Guns

Do not use a pneumatic tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating pneumatic tools may result in serious personal injury. · Dress properly. Do not wear loose clothing of jewelry. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewelry or long hair can be caught in moving parts. Air vents often cover moving parts and should be avoided. · Always use the appropriate eye and ear protection and oth

Northern Industrial Tools 6317D

downloaded: 0File size: 167 kb    Manafacture: Northern Industrial Tools  
Category: Power Screwdrivers and Drills

Reversing switch lever 2. Clockwise 3. Counterclockwise 001895 Reversing switch action This tool has a reversing switch to change the direction of rotation. Depress the reversing switch lever from the A side for clockwise rotation or from the B side for counterclockwise rotation. When the reversing switch lever is in the neutral position, the switch trigger cannot be pulled. CAUTION: • Always check the direction of rotation before operation. • Use the reversing switch only after the tool comes t





Category