Next, place shoulder spacer (V) and hex bo!t (U) through tow bar and frame. Secure with hex nut (W). See figure 15. Repeat for other side. 3. Secure the two tow bar ends together with truss machine screw (X), lock washer (Y) and hex nut (Z). See figure 15. To attach the tow bar to a hitch, place the shouldf bolt (AA) up through the tow bar. Place one bellevi^ washer (AB) on the shoulder bolt, then the hitch plate and the other belleville washer. Cupped side of the washers must be against the h

Insert hex bolts through holes in support brackets and fenders. Secure with flat washers, lock washers and hex nuts. See figure -8. Tighten securely. ATTACHING THE CONTROL HANDLE 1. The control handle is taped to the stripper half for shipping purposes only. Remove the tape. 2. The bottom of the control handle is already attached to the valve. Remove the cotter pin and clevis pin which are attached to the valve. Place the handle in position, and secure to the valve —— using the cotter pin a

214-200A assembly 214-255A VERTICAL ROTARY TILLERS yrnrrmTrrrrrrrrrrrrrerrrrrrrrrrrrrrmrrrrrroTffrrrrrrïifTrrnr^^ WARRANTY mr*» For one year from date of purchase, MTD Products Inc will replace for the original purchaser, free of charge, F.O.B. factory or authorized service firm, any part or parts found to be defective in material or workmanship. All transportation charges on parts submitted for replacement under this warranty must be paid by the purchaser. This warranty does not include r

x 1.00" O.D. 33 14571 -- 488 Caster Arm Ass'y. x .305" Lg.t 34 08348 Drive Shaft .624" Dia. x 74 736-0175 L-Wash. .265" I.D.t 22.75" Lg.t 75 710-0352 Hex Self Tap Scr. 1/4" x ^5 748-0136 Bevel Gear .50" I.D. x 14 3/8" Lg.t Teeth t 76 14556 R.H. Pinion Guard t 36 748-0108 Flange Bearing .503" I.D. t 14555 L.H. Pinion Guard (Not Shown) 37 08189 Gear Box t 77 712-0298 Hex Jam Nut 1 /4-20 Thd. t 38 748-0110 Flange Bearing .630" I.D. t 78 736-0242 Belle

NO. PART NO. CODE DESCRIPTION REF. NO. PART NO. CODE DESCRIPTION 1 710-0874 Hex Bolt 5/16-18 x 1.25" Lg. 31 736-0140 FI-Wash. .385" I.D. x .62" O.D. 2 712-3004A Hex Flange L-Nut 5/16-18 Thd. 32 720-0270 Grip-Reverse Lever (Gr. 5) 33 686-0014 Reverse Handle Ass’y. 3 786-0004 Tail Piece Brkt. (R.H.) 34 726-0135 Cap Speed Nut 4 786-0003 Tail Piece Brkt. (L.H.) 35 731-1645 Clutch Handle Holder 5 710-0442 Hex Bolt 5/16-18x1.5" Lg. 36 720-0269 Grip-Clutch 7 750-0890 Spacer .32" I

6/98 9 Handlebars, Controls, and Shrouds (Continued) Models 938001,002,003,004,00 5,007,008,009,301,301 *,302,303 Item No. Part No. Qty. Description 43 07517700 1 Cap-lgnition Switch 44 06517300 1 Nut-Panel .625-32 45 07527800 1 Plug-Hole .50 Diameter (001,003,006,008,301,301*,303) 46 02456500 1 Key Switch Assembly 47 06216900 4 Bolt-Round Head Square Neck .25-20 x 1.75 48 03803800 1 Guide-Rope 49 06111200 2 Screw-Machine 10-24 x .750 50 07518200 1 Primer Assembly 51 06930500 1 Ca

Remove the outer tine assembly and turn around so that the sharp edge of the tines enter the soil first. Secure with bolt and lock-nut. See page 14. 4. NEVER place hands or feet in the vicinity of the tines while the engine is running. 5. Always stop engine when tiller is not in actual use. 6. Always disconnect spark plug wire during repairs or refueling operations. 7. Do not fill gas tank while engine is running. Do not spill gasoline on hot engine. WHEELS Insert axle bolt into wheel plac

Place rubber washer (M) on shoulder bolt. Secure to bracket with lock washer (G) and hex nut (N). 7 I FIGURE 9 ENGAGEMINT HANDLE. PLUNGER ^ ON PUMP 5. 6. Place the engagement handle in reverse position, locked in the notch in the slotted bracket. See figure 10. Adjust the engagement rod by tightening the hex nut on the end of the rod until the plunger on tht pump is pushed all the way in when the engagement handle is locked in the reverse position. Insert a screwdriver into the slot in

Small branches up to 1/2" diameter can also be fed into the shredder in this position. See figure 11. FIGURE 8.—Model 645 Shown T ...........[U,MUI„ FIGURE 10. No Larger Than 1/2" Diameter FIGURE 11. 3. To lower the leaf ramp, use one hand to grasp the handle at the top of the leaf ramp and lift slightly. Pull up on the release bar, and lower the leaf ramp to the ground. Release the bar. See figure 12. Bulky material, such as stalks or heavy branches, up to 3" in diameter should be fed

6) • Insert end of shift rod into hole of shift lever indicator. • Insert hairpin clip through hole of shift rod to secure with bend of clip on right side. • Grasp handle assembly. Hold in “up” position. Ensure handle lock remains in gearcase notch. Slide handle assembly into position. Fig. 4 HANDLE ASSEMBLY "UP" POSITION LOOSEN HANDLE LOCK LEVER TO MOVE TIGHTEN HANDLE LOCK LEVER TO HOLD • Rotate handle assembly down. Insert rear carriage bolt first, with bolt head on L.H. side of tiller and loo