Votes - 1, Average rating: 5 ( )

Manafacture: Citizen File size: 600.72 kb File name: SRP350II_user_manual.pdf Language of manual:

1.00 - 9 - SRP-350II 1-2-3 USB Interface USB IFG-U TYPE Drawer kick-out connector Power supply connector USB connector Pin No. Signal Name Assignment (Color) Function Shell Shield Drain Wire Frame Ground 1 VBUS Red Host Power : DC5[V] / 500[mA] 2 D-White Differential Data Line 3 D+ Green Differential Data Line 4 GND Black Signal Ground 1-3 Connecting the Drawer . WARNING Use a drawer that matches the printer specification. Using an improper drawer may damage the drawer as well as the printer. . CAUTION Do not connect a telephone line to the drawer kick-out connector; otherwise the printer and the telephone line may be damaged. Plug the drawer cable into the drawer kick-out connector on the back of the printer next to the power supply connector. Pin No. Signal name Direction 1 Frame GND - 2 Drawer Kick-Out Driver Signal #1 Output 3 Drawer Open / Close Signal Input 4 +24V - 5 Drawer Kick-Out Driver Signal #2 Output 6 Signal GND - Rev. 1.00 - 10 SRP-350II 1-4 Setting the Dip Switches 1-4-1 Serial Interface • DIP Switch 1 SW Function ON OFF Default 1-1 Auto Line Feed Enable Disable OFF 1-2 Flow Control XON/XOFF DTR/DSR OFF 1-3 Data Length 7 bits 8 bits OFF 1-4 Parity Check Yes No OFF 1-5 Parity Selection EVEN ODD OFF 1-6 OFF 1-7 Baud rate Selection (bps) Refer to the following Table 1 ON 1-8 OFF • DIP Switch 2 SW Function ON OFF Default 2-1 Auto cutter control Full cut Partial cut OFF 2-2 Internal bell control Internal bell disable Internal bell enable OFF 2-3 Auto Cutter Auto cutter disable Auto cutter enable OFF 2-4 Reserved --OFF 2-5 OFF 2-6 Print Density Refer to the following table 2 OFF 2-7 Near-End Sensor Status Disable Enable OFF 2-8 External buzzer control External buzzer enable External buzzer disable OFF 1-4-2 Parallel & USB Interface • DIP Switch 1 SW Function ON OFF Default 1-1 Auto Line Feed Enable Disable OFF 1-2 Reserved --OFF 1-3 Reserved --OFF 1-4 Reserved --OFF 1-5 Reserved --OFF 1-6 Reserved --OFF 1-7 Reserved --ON 1-8 Reserved --OFF • DIP Switch 2 SW Function ON OFF Default 2-1 Auto cutter control Full cut Partial cut OFF 2-2 Internal bell control Internal bell disable Internal bell enable OFF 2-3 Auto Cutter Auto cutter disable Auto cutter enable OFF 2-4 Reserved --OFF 2-5 OFF 2-6 Print Density Refer to the following table 2 OFF 2-7 Near-End Sensor Status Disable Enable OFF 2-8 External buzzer control External buzzer enable External buzzer disable OFF Rev. 1.00 - 11 SRP-350II • Table 1 – Baud rate (bps) Selection Transmission Speed 1-6 1-7 1-8 Default 2400 ON OFF OFF 9600 4800 ON OFF ON 9600 OFF ON OFF 19200 OFF OFF OFF 38400 OFF ON ON 57600 OFF OFF ON 115200 ON ON ON • Table 2 – Print Density Selection Print Density 2-5 2-6 Default 1 (Light) ON ON 22 (Medium) OFF OFF 3 (Dark) OFF ON . Auto Cutter Enable / Disable selection Dip Switch Set 2 SW 2-3 ON Auto Cutter Disabled OFF Auto Cutter Enabled Application Ignores Auto Cutter error for continuous printing. Rev. 1.00 - 12 SRP-350II 1-5 Installing or Replacing the Paper Roll . NOTE Be sure to use paper rolls that meet the specifications. Do not use paper rolls that have the paper glued to the core because the printer cannot detect the paper end correctly. 1-5-1 Make sure that the printer is not receiving data; otherwise, data may be lost. 1-5-2 Open the paper roll cover by pressing the cover-open button. . NOTE Do not open the print cover while the printer is operating. This may damage the printer. 1-5-3 Remove the used paper roll core if there is one. 1-5-4 Insert the paper roll as shown. Rev. 1.00 - 13 SRP-350II 1-5-5 Be sure to note the correct direction that the paper comes off the roll. 1-5-6 Pull out a small amount of paper, as shown. Then close the cover. . NOTE When closing the cover, press the center of printer cover firmly to prevent paper miss-loading. 1-5-7 Tear off the paper as shown. Rev. 1.00 - 14 SRP-350II 1-6 Adjustments and Settings The SRP-350II is set up at the factory to be appropriate for almost all users. It does, however, offer some settings for users with special requirements. It has DIP switches that allow you to change communication settings, such as handshaking and parity check, as well as print density. The SRP-350II also has a near-end sensor for the paper. This can give you a warning when the paper is almost out. If you find that there is not enough paper remaining on the roll when the near-end sensor is triggered, you can change the near-end sensor setting. Rotate the near end sensor tab at front or rear position. (See the below figure) Near end sensor tab 1-7 Using the Printer Control Panel 0 POWER The POWER light is on whenever the printer is on. 0 ERROR This indicates an error. 0 PAPER This light indicates the near end of the paper roll. Install a new paper roll and the printer will continue printing. When the light blinks, it indicates the self-test printing standby state or macro execution Standby state when the macro execution command is used. 0 FEED Press the FEED button once to advance paper one line. ...

Download now

Please, enter two numbers from picture: